Bedienungsanleitung Harman Kardon AVR142 (Seite 8 von 24) (Englisch)

502641

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

FED

12 0 6 C 7 8 9 A

B4 G 5 H

AVR 142

FRONT PANEL CONTROLS

AVR Audio/Video Receiver

Front Panel Controls



Main Power Switch: Press this button to apply

power to the AVR. When the switch is pressed in, the

unit is placed in a Standby mode, as indicated by the

orange LED



. This button MUST be pressed in to

operate the unit. To turn the unit off completely and

prevent the use of the remote control, this switch

should be pressed until it pops out from the front

panel so that the word “OFF” may be read at the top of

the switch.

NOTE

: This switch is normally left in the “ON” position.



System Power Control: When the Main Power

Switch



is “ON,” press this button to turn on the

AVR; press it again to turn the unit off (to Standby).

Note that the Power Indicator



will turn blue

when the unit is on.



Power Indicator: This LED will be illuminated in

orange when the unit is in the Standby mode to signal

that the unit is ready to be turned on. When the unit is

in operation, the indicator will turn blue.



Headphone Jack: This jack may be used to listen

to the AVR’s output through a pair of headphones.

Be certain that the headphones have a standard 6.3

mm stereo phone plug. Note that the speakers will

automatically be turned off when the headphones are

connected.



Digital Optical 3 Input: Connect the optical

digital audio output of an audio or video product to

this jack.



Aux input stereo minijack: Connect this

minijack to any audio source, typically MP3 players or

portable CD players. An analog headphone output jack

or line level out jack may be used.



Surround Mode Group Selector: Press this

button to select the top-level group of surround

modes. Each press of the button will select a major

mode grouping in the following order:

Dolby Modes

DTS Digital Modes

DSP Modes

Stereo Modes

Logic 7 Modes

Once the button is pressed so that the name of the

desired surround mode group appears in the Lower

Display Line



, press the Surround Mode

Selector



to cycle through the individual modes

available. For example, press this button to select

Dolby modes, and then press the Surround Mode

Selector



to choose from the various mode

options.



Tuning Selector: Press the left side of the

button to tune lower frequency stations and the right

side of the button to tune higher frequency stations.

When a station with a strong signal is reached,

e

e

will appear

in the Main Information Display



(see page 20

for more information on tuning stations).



Tuner Band Selector: Pressing this button will

automatically switch the AVR to the Tuner mode.

Pressing it again will switch between the AM and FM

frequency bands, holding it pressed for some seconds

will switch between stereo and mono receiving and

between automatic and manual tuning mode (See

page 20 for more information on the tuner).



Preset Stations Selector: Press this button to

scroll up or down through the list of stations that have

been entered into the preset memory. (See page 20 for

more information on tuner programming.)



Input Source Selector: Press this button to

change the input by scrolling through the list of input

sources.



RDS Select Button: Press this button to display

the various messages that are part of the RDS data

system of the AVR’s tuner. (See page 20 for more

information on RDS).



Surround Mode Selector: Press this button

to select from among the available surround mode

options for the mode group selected. The specific

modes will vary based on the number of speakers

available, the mode group and if the input source is

digital or analog. For example, press the Surround

Mode Group Selector



to select a mode grouping

such as Dolby or Logic 7, and then press this button to

see the mode choices available. For more information

on mode selection, see page 13.



Volume Control: Turn this knob clockwise to

increase the volume, counterclockwise to decrease the

volume. If the AVR is muted, adjusting volume control

will automatically release the unit from the silenced

condition.



Remote Sensor Window: The sensor behind

this window receives infrared signals from the remote

control. Aim the remote at this area and do not

block or cover it unless an external remote sensor is

installed.



Main Information Display: This display delivers

messages and status indications to help you operate

the receiver.



Digital Coax 3 Input: This jack is normally used

for connection to the output of portable digital audio

devices, video game consoles or other products that

have a coax digital jack.



Video 3 Input Jacks: These audio/video jacks

may be used for temporary connection to video games

or portable audio/video products such as camcorders

and portable audio players.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR142 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR142

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info