502641
10
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
10
INSTALLATION AND CONNECTIONS
Installation and Connections
After unpacking the unit, and placing it on a solid
surface capable of supporting its weight, you will
need to make the connections to your audio and video
equipment.
Audio Equipment Connections
We recommend that you use high-quality interconnect
cables when making connections to source equipment
and recorders to preserve the integrity of the signals.
When making connections to audio source equipment
or speakers it is always a good practice to unplug
the unit from the AC wall outlet. This prevents any
possibility of accidentally sending audio or transient
signals to the speakers that may damage them.
Important Note: In order to clearly identify all
connectors and simplify nstallation, as per the new
EIA/CEA-863 standard, all connections are colour
coded as follows:
For Speakers and Audio In/Outputs: White (Left,
speakers front) and Red (Right, speakers front).
For Speakers: Green (Center), Blue (Left Surround) and
Grey (Right Surround).
For Audio Output: Purple (Subwoofer).
For Composite Video In/Outputs: Yellow.
For Digital Audio In/Outputs: Orange.
Connect the analog output of a CD player to the 1. CD
inputs
.
NOTE: When the CD player has both fixed and variable
audio outputs it is best to use the fixed output unless
you find that the input to the receiver is so low that the
sound is noisy, or so high that the signal is distorted.
Connect the analog Play/Out jacks of a cassette 2.
deck, MD, CD-R or other audio recorder to the
Tape Input jacks
. Connect the analog Record/
In jacks on the recorder to the Tape Output jacks
on the AVR.
Connect the output of any digital sources to
3.
the appropriate input connections on the AVR
rear panel. Note that the Optical and Coaxial
digital inputs


may be used with
a Dolby Digital or DTS source or the output of a
conventional CD, MD or LD player’s PCM (S/P-DIF)
output.
Assemble the AM Loop Antenna supplied with the 4.
unit as shown below. Connect it to the AM and
GND screw terminals
.
Connect the supplied FM antenna to the 5. FM
(75 ohm) connection
. The FM antenna may
be an external roof antenna, an inside powered
or wire lead antenna or a connection from a cable
system. Note that if the antenna or connection
uses 300-ohm twin-lead cable, you must use
a 300-ohm-to-75-ohm adapter to make the
connection.
Connect the front, center and surround speaker 6.
outputs to the respective speakers.
To assure that all the audio signals are carried to
your speakers without loss of clarity or resolution,
we suggest that you use high-quality speaker cable.
Many brands of cable are available and the choice of
cable may be influenced by the distance between your
speakers and the receiver, the type of speakers you use,
personal preferences and other factors. Your dealer or
installer is a valuable resource to consult in selecting
the proper cable.
Regardless of the brand of cable selected, we
recommend that you use a cable constructed of fine,
multistrand copper with an area greater than 2 mm
2
.
Cable with an area of 1.5 mm
2
may be used for short
runs of less than 4 m. We do not recommend that you
use cables with an area less than 1mm
2
due to the
power loss and degradation in per for mance that will
occur.
When connecting wires to the speakers, be certain
to observe proper polarity. Remember to connect the
negative or “black” wire to the same terminal on both
the receiver and the speaker. Similarly, the positive” or
red” wire should be connected to like terminals on the
AVR and speaker.
NOTE: While most speaker manufacturers adhere
to an industry convention of using black terminals
for negative and red ones for positive, some
manufacturers may vary from this configuration.
To assure proper phase and optimal performance,
consult the identification plate on your speaker or
the speaker’s manual to verify polarity. If you do not
know the polarity of your speaker, ask your dealer
for advice before proceeding, or consult the speaker’s
manufacturer.
We also recommend that the length of cable used to
connect speaker pairs be identical. For example, use
the same length piece of cable to connect the front-
left and front-right or surround-left and surround-right
speakers, even if the speakers are a different distance
from the AVR.
Connections to a subwoofer are normally made via
7.
a line level audio connection from the Subwoofer
Output
to the line-level input of a subwoofer
with a built-in amplifier. When a passive
subwoofer is used, the connection first goes to a
power amplifier, which will be connected to one or
more subwoofer speakers.
If you are using a powered subwoofer that does
not have line-level input connections, follow
the instructions furnished with the speaker for
connection information.
Note
: Speaker sets with two front satellites and
a passive subwoofer must be connected to the
front speaker outputs only rather than to the
Subwoofer Output
.
If an external multi-channel audio source with
8.
5.1 outputs such as an external digital processor/
decoder, DVD-Audio or SACD™ player is used,
connect the outputs of that device to the
6-Channel Direct Inputs
.
Video Equipment Connections
Video equipment is connected in the same manner
as audio components. Again, the use of high-quality
interconnect cables is recommended to preserve signal
quality.
Connect a VCR’s audio and video Play/Out jacks to 1.
the Video 2 In jacks
G
on the rear panel. The
Audio and Video Record/In jacks on the VCR should
be connected to the Video 1 Out jacks

on the AVR.
Although any video device may be connected to 2.
these jacks, we recommend connecting your TV to
the Video 1 Audio/Video Input Jacks

so
that you may take advantage of the fact that the
remote control is preprogrammed with TV product
codes for the Video 1 device.
For the same reason, we recommend connecting
your video recorder, cable TV converter or satellite
receiver to the Video 2 Audio/Video Input
Jacks
G
.
Connect the analog audio and video outputs of a
3.
DVD to the DVD jacks

. This is valid only
if your DVD player does not have a HDMI Output.
If a HDMI Output is available on the DVD player,
connect it to the HDMI Inputs
. Please note
that these Inputs are Video only. Audio must be
connected separately.
Connect the digital audio outputs of a CD, MD or
4.
DVD player, satellite receiver, cable box or HDTV
converter to the appropriate Optical or Coaxial
Digital Inputs


.
Remember that the DVD source defaults to the
Coaxial 1 Digital Input
. All other sources
default to their analog inputs, although any source
may be assigned to any digital audio input on the
receiver.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Harman Kardon AVR142 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Harman Kardon AVR142

Harman Kardon AVR142 Bedienungsanleitung - Deutsch - 24 seiten

Harman Kardon AVR142 Bedienungsanleitung - Holländisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info