Bedienungsanleitung Harman Kardon AVR142 (Seite 13 von 24) (Englisch)

502641

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

System Configuration

SYSTEM CONFIGURATION

Press the 5. OK button



again, and use the



buttons

on the remote to select the option

that best describes your system based on the

Center speaker definitions shown in preceding

section.

When



is selected, low frequency center

channel sounds will be sent to the Fronts, if they are

set for



and Sub is turned off. When Sub is on,

low frequency center channel sounds will be sent to

the subwoofer only.

When



is selected, a full-range output will be

sent to the center speaker output, and with analog and

digital surround modes (except with the Pro Logic II

Music mode) NO center channel signal will be sent to

the subwoofer output.

When



is selected, no signal will be sent to

the center channel output. The receiver will operate

in a “phantom” center channel mode and center

channel information will be sent to the left and right

front channel outputs and its bass will be sent to

the subwoofer output too as long as SUB L/R+LFE

is selected in the SUBWOOFER line in this menu (see

below). This mode is needed if no Center speaker is

used. Note that for the use of Logic 7C surround mode

a Center speaker is needed, but Logic 7M works well

without a Center too.

When you have completed your selection for the 6.

center channel, press the OK button



, and

then press the



buttons

on the remote

to change the display to

e

Press the

7. OK button



again, and then use the



buttons

on the remote to select the

option that best describes your system based

on the Surround speaker definitions shown in

preceding section.

When



is selected, with all digital surround

modes low frequency surround channel sounds will

be sent to the Fronts, when Sub is turned off, or to the

subwoofer output when Sub is on. With the analog

surround modes the rear bass feed depends on the

mode selected and the setting of the sub and front

speakers.

When



is selected, a full-range output will be

sent to the surround channel outputs (with all analog

and digital surround modes), and, except with Hall

and Theater modes, NO surround channel bass will be

sent to the subwoofer output.

When



is selected, surround sound information

will be split between the front-left and front-right

outputs. Note that for optimal performance when no

surround speakers are in use, the Dolby 3 Stereo mode

should be used instead of Dolby Pro Logic.

When you have completed your selection for the 8.

surround channel, press the OK button



, and

then press the



buttons

on the remote

to change the display to

Ie

Press the

9. OK button



, and then press the



buttons

on the remote to select the option

that best describes your Subwoofer system.

The choices available for the subwoofer position

will depend on the settings for the other speakers,

particularly the front left/right positions.

If the front left/right speakers are set to



, the

subwoofer will automatically be set to



, which is

the “on” position.

If the front left/right speakers are set to



three options are available:

If no subwoofer is connected to the AVR, press the

arrow buttons

so that

e

appears

in the display. When this option is selected, all bass

information will be routed to the front left/right

“main” speakers.

If a subwoofer is connected to the AVR, you have

the option to have the front left/right “main”

speakers reproduce bass frequencies at all times,

and have the subwoofer operate only when

the AVR is being used with a digital source that

contains a dedicated Low Frequency Effects, or

LFE soundtrack. This allows you to use both your

main and subwoofer speakers to take advantage

of the special bass created for certain movies. To

select that option press the arrow buttons

that

e

appears in the display.

If a subwoofer is connected and you wish to use it

for bass reproduction in conjunction with the main

front left/right speakers, regardless of the type of

program source or surround mode you are listening

to, press the arrow buttons

so that

eed

Z

appears in the display. When this option

is selected, a “complete” feed will be sent to the

front left/right “main” speakers, and the subwoofer

will receive the front left and right bass frequencies

under the crossover frequency 80 Hz, additionally

to the LFE soundtrack (see above).

When all speaker selections have been made for 10.

the input selected, press the OK button



twice

or simply wait for three seconds until the display

returns to the normal mode.

Surround Setup

Once the speaker setup has been completed, the next

setup step is to set the surround mode you wish to use

with each input. Since surround modes are a matter of

personal taste, feel free to select any mode you wish –

you may change it later. To make it easier to establish

the initial parameters for the AVR, it is best to leave the

default setting of Logic 7 Music mode for most analog

inputs and Dolby Digital for inputs connected to digital

sources. In the case of inputs such as a CD Player, Tape

Deck or Tuner, you may wish to set the mode to Stereo,

if that is your preferred listening mode for standard

stereo sources, where it is unlikely that surround

encoded material will be used.

To set the surround mode you wish to use with the

input selected, press the Surround Mode Selector

button



on the front or

on the remote

until the desired surround mode´s name appears in

the Main Information Display



Note that Dolby Digital and DTS will only appear as

choices when a digital input has been selected.

After the surround mode setting has been made with

the current input, repeat the setting with all inputs

you will use. The surround mode can also be changed

at any time later, and the AVR’s memory system will

keep the settings for the input selected, until they are

changed again.

Configuring the Surround Off

(Stereo) Modes

For superior reproduction of two-channel program

materials, the AVR offers two Stereo modes: an

analog Stereo-Direct mode that bypasses the digital

signal processing circuitry for a completely analog

signal path that preserves the purity of the original

signal, and a digital mode that is capable of providing

bass management for optimal distribution of the

low frequencies between smaller speakers and a

subwoofer.

Stereo-Direct (Bypass) Mode

When the analog Stereo-Direct mode is selected

by pressing the Stereo Mode Selector



until

e

appears in the Main

Information Display



the AVR will pass the

analog source material directly through to the front left

and right speakers, bypassing the digital processing

circuitry.

In this mode, the front left and right speakers will

automatically be configured as



; it is not

possible to configure these speakers as



Harman Kardon AVR142 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR142

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info