Bedienungsanleitung Harman Kardon AVR247 (Seite 15 von 76) (Englisch)

502596

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

REMOTE CONTROL FUNCTIONS

Sleep Button: Press this button to activate the sleep timer, which turns

off the receiver after a programmed period of time of up to 90 minutes.

Volume Controls: Press these buttons to raise or lower the volume,

which will be shown in decibels (dB) in the Message Display.

DSP Surround: Press this button to select a DSP surround mode

(Hall 1, Hall 2, Theater).

On-Screen Display (OSD): Press this button to activate the

on-screen menu system.

Multiroom: Press this button to control the multiroom system. Three

settings are available: MULTI ON/OFF, which is used to turn the multiroom

system on or off; MULTI LEVEL, which adjusts the volume of the remote

zone only; and MULTI INPUT, which is used to select the source input for

the remote zone. See Multiroom Operation in the Advanced Functions

section for more information on using the AVR 247’s multiroom system.

Channel Level: Press this button to adjust the output levels for each

channel so that all speakers sound equally loud at the listening position.

Usually this is done while playing an audio selection, such as a favorite CD,

after you have calibrated the levels using EzSet/EQ, as described in the Initial

Setup section.

Speaker Setup: Press this button to configure speaker sizes, that is,

the low-frequency capability of each speaker. Usually this is done using

the on-screen menu system, as described in the Initial Setup section.

Navigation (

⁄

‹

›

) and Set Buttons: These buttons are

used to make selections within the on-screen menu system, or when

accessing the functions of the four buttons surrounding this area of the

remote – Channel Level, Speaker Setup, Digital Input or Delay.

Digital Input Select: Press this button to select the specific digital

audio input (or analog audio input) you used for the current source.

Delay: Press this button to set delay times that compensate for placing

the speakers at different distances from the listening position, or to

resolve a “lip sync” issue that may be caused by digital video processing.

This may also be done using the on-screen menu system, as described

in the Initial Setup section.

Numeric Keys: Use these buttons to enter radio station frequencies

or to select station presets. When the AM or FM band is in use, press

the Direct Button before entering the station frequency.

When listening to XM Radio, you may enter channel numbers without first

pressing the Direct Button; however, to access the preset stations, you will

need to use the Preset Stations Selectors. To access another bank of XM

presets, press the Set Button repeatedly until PRESET SEARCH appears,

then use the

⁄

Buttons to select the letter of the desired bank.

Tuning Mode: When listening to AM or FM radio, this button toggles

between manual (one frequency step at a time) and automatic (seeks

frequencies with acceptable signal strength) tuning mode. It also toggles

between stereo and mono modes when an FM station is tuned.

When listening to XM Radio, press the Tuning Mode Button once to view

the category name of the current channel. Additional presses will display

the artist, song title and channel name.

Memory: After you have tuned a particular radio station, press this

button, then the numeric keys, to save that station as a radio preset.

For XM Radio, the procedure for saving a preset is a little different. To

save the current channel in one of the 40 available preset locations,

press the Set Button repeatedly until PRESET SEARCH appears. Use

the

⁄

Buttons to select a letter (A through E) representing one of

the five banks of preset memory slots. Then press the Memory Button,

followed by a Numeric Key (1 through 8) for the precise preset memory

location you wish to save the channel in.

Tuning: Press these buttons to tune a radio station or XM Radio

channel. For the AM and FM bands, and depending on whether the

tuning mode has been set to manual or automatic, each press will either

change one frequency step at a time, or seek the next frequency with

acceptable signal strength.

Direct: Press this button before using the Numeric Keys to directly

enter a radio station frequency (AM or FM bands only).

Clear: Press this button to clear a radio station frequency you have

started to enter.

Preset Stations Selector: Press these buttons to select a preset

radio station.

For XM Radio, first press the Set Button repeatedly until PRESET SEARCH

appears and then use the

⁄

Buttons to select the letter of the

desired bank of presets.

Tone Mode: Press this button to access the tone controls (bass and

treble). Use the Navigation Buttons to make your selections.

Disc Skip: This button has no effect on the receiver, but is used with

some optical disc changers to skip to the next disc.

Macros: These buttons may be programmed to execute long command

sequences with a single button press. They are useful for programming the

command to turn on or off all of your components, or for accessing special-

ized functions for a different component than you are currently operating.

Surround Mode Selectors: Press any of these buttons to select

a type of surround sound (e.g., multichannel) mode. Choose from the

Dolby modes, DTS modes, Logic 7 modes or Stereo modes. Each

press of a button will cycle to the next available variant of that mode.

Not all modes or mode groups are available with all sources.

Night Mode: Press this button to activate Night mode with specially

encoded Dolby Digital discs or broadcasts. Night mode compresses the

audio so that louder passages are reduced in volume to avoid disturbing

others, while dialogue remains intelligible.

Track Skip: These buttons have no effect on the receiver, but are

used with many source components to change tracks or chapters.

Dim: Press this button to partially or fully dim the front-panel display.

Transport Controls: These buttons have no effect on the receiver,

but are used to control many source components. By default, when the

remote is operating the receiver, these buttons will control a DVD player.

AVR247om.qxd 7/10/07 1:05 PM Page 15

Harman Kardon AVR247 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info