Bedienungsanleitung Harman Kardon AVR254 (Seite 37 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INITIAL SETUP

Europe and elsewhere. The AVR 254 is capable of detecting PAL

video sources and converting them to the NTSC format for display on

American televisions.

Adjust Lip Sync: Use this adjustment to resynchronize the audio and

video signals from a source to eliminate a “lip sync” problem. Lip sync

issues can occur when the video portion of a signal undergoes additional

processing in either the source or the video display that desynchronizes

it from the audio. Select this line to display the Lip Sync adjuster by

itself, enabling you to view the video while listening to the audio. Use the

‹

›

Buttons to delay the audio by up to 180ms. See Figure 51.

Figure 51 – Adjust Lip Sync

Change Name: Use this line to change the display name for your

source. This can be useful if your source’s device type is different from

the available source names. Select this line and use the

⁄

Buttons

to scroll forward or reverse through the letters A through Z and the

numbers 0 through 9. When the desired character appears, use the

›

Button to move the cursor to the next position. Move the cursor again

to leave a blank space. When you have finished entering the new name,

press the OK Button. The name will be used on the front panel to refer

to the source, and will appear next to its original name, e.g. DVD,

throughout the on-screen menu system. To clear the entry without

making any changes, scroll to the blank character between “9” and “A”.

Audio Auto Polling: Use this setting when both analog and digital audio

connections are made from the source device to the AVR. When no

digital signal is present, the AVR will automatically switch to the analog

audio input.

This can be useful for some older cable television systems that broad-

cast some channels in analog audio and others in digital audio. It is also

useful for making analog recordings of copy-protected digital sources,

and for multichannel disc players that decode high-resolution multichannel

audio and output it through their multichannel analog audio outputs.

However, it can be inconvenient when no analog audio connection is

made and playback is stopped, as the audio signal will be lost.

If an analog audio connection was made, select it here. If not, choose

the Off setting, and the AVR will always use the digital audio connection.

Zone 2 Audio: When a multizone system has been connected and is

in use, this setting determines the source for the remote zone. Select

the analog audio input the source is connected to. Digital audio is not

available to the multizone system, nor is any type of video.

Use the Back/Exit Button to exit, then return to the Setup Source line of

the Main Menu and select the next source to configure. When you have

finished configuring all sources, press the Back/Exit Button to clear the

menus from view.

You are now ready to begin enjoying your new receiver!

AVR254om.qxd 3/28/08 12:46 PM Page 37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info