Bedienungsanleitung Harman Kardon AVR254 (Seite 36 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INITIAL SETUP

Audio Input from source: Select this line to assign the correct analog

or digital audio input to the source. Refer to Table A5 in the appendix,

where you noted the physical audio input the source is connected to,

and select the input here. If both analog and digital audio connections

were made, select the digital input here, and select the analog input at

the Audio Auto Polling line below.

6-/8-Channel Direct Inputs

The 6-/8-Channel Analog Audio Inputs are used when playing certain

multichannel discs, such as DVD-Audio, Blu-ray Discs, SACD and

HD-DVD, on a player that decodes the audio and outputs it via its

multichannel analog audio outputs but not via its HDMI output.

HDMI-equipped multichannel disc player:

• Connect the player’s HDMI output to one of the AVR’s HDMI Inputs.

No other connections are necessary.

• Assign the HDMI Input to both the Audio and Video Input from source

settings in the Source Info menu.

HDMI-equipped multichannel disc player that does not output

multichannel audio via an HDMI connection:

• Connect the player’s HDMI output and its multichannel analog

audio outputs to one of the AVR’s HDMI Inputs and to the AVR’s

6-/8-Channel Analog Audio Inputs.

• Assign the HDMI Input to both the Audio and Video Input from source

settings in the Source Info menu.

• Assign the 6-/8-Channel Analog Audio Inputs to the Audio Auto

Polling setting in the Source Info menu.

• When listening to DVD-Video discs, CDs or other materials outputting

standard-definition digital audio, do nothing, as long as the HDMI Input

is assigned to the Audio Input from source setting.

• When listening to high-resolution multichannel discs, the AVR’s auto

polling feature will automatically switch to the multichannel analog

audio inputs.

Multichannel disc player without HDMI output, or when video

display has no HDMI input:

• Connect the player’s component video outputs to one set of Component

Video Inputs on the AVR. Depending on the capabilities of the player

and your video display, you may need to use a composite or S-video

connection instead.

• Connect the player’s digital audio output to a corresponding available

digital audio input on the AVR.

• Connect the player’s multichannel audio outputs to the AVR’s

6-/8-Channel Analog Audio Inputs.

• Assign the correct audio and video inputs to the Audio and Video

Input from source Settings in the Source Info menu.

• Assign the 6-/8-Channel Analog Audio Inputs to the Audio Auto

Polling setting in the Source Info menu.

• When listening to DVD-Video discs, CDs or other materials outputting

standard-definition digital audio, do nothing, as long as the correct

digital audio input is assigned to the Audio Input From Source setting.

• When listening to high-resolution multichannel discs, the AVR’s auto

polling feature will automatically switch to the multichannel analog

audio inputs.

NOTE: The 6-/8-Channel Inputs pass the incoming signals

directly to the volume control, without digitizing or processing

them. Configure the bass management settings (i.e., speaker

size, delay and output level) on your source device to match

the settings programmed using the EzSet/EQ procedure, which

may be viewed using the Speaker Setup menu (see Advanced

Functions section). Consult the owner’s guide for your multi-

channel player for more information.

Resolution to Display: This setting, which may also be accessed from

the AVR Settings menu, reflects the video output resolution, which is

dependent upon the capabilities of the video display.

• If the display is connected to the AVR’s HDMI Output, the HDMI pro-

tocol enables the two devices to communicate with each other, and

the AVR will automatically select the correct video output resolution.

• If the display is connected to the AVR’s Component Video Outputs,

there is no automatic detection of the display’s capabilities, and the

video output resolution must be manually adjusted to match the

display’s capabilities (which may be obtained from the display’s

manual or its manufacturer’s Web site).

• If the display is connected to the AVR’s Composite or S-Video Monitor

Output, the video output resolution must be manually set to 480i to

view any content, including the AVR’s own menus.

Since there is no picture if the resolution is set higher than the display’s

capability, adjust the resolution by pressing the front-panel Resolution

Button repeatedly until the correct setting appears in the front-panel

Message Display. For composite and S-video, the correct setting is

480i. For component video, it is the highest resolution where a picture

is visible. You will be prompted to accept or cancel the resolution

change, as the CANCEL message will appear on the front panel.

Press the

Button to view the ACCEPT option, and then press the

OK Button to complete the change to the output resolution.

NOTE: When the display has a DVI input which is connected

to the AVR using an HDMI-to-DVI adapter, the picture will be

distorted or blank if the display is not HDCP-compliant. In that

case, a different video connection must be used (component,

composite or S-video).

Resolution from Source: This line, which is informational only, indi-

cates the video format (NTSC or PAL) output by the source device.

NTSC is the video format used for standard-definition television in the

U.S. and other parts of the world. The PAL format is used in parts of

AVR254om.qxd 3/28/08 12:46 PM Page 36

Harman Kardon AVR254 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info