Bedienungsanleitung Harman Kardon AVR254 (Seite 34 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INITIAL SETUP

Figure 45 – Plug EzSet/EQ microphone into receiver.

Step Three – Make sure that the AVR 254 and the video display are

turned on. Press the AVR Settings Button to display the Main Menu. See

Figure 43. Use the

Button to highlight the Speaker Setup line, and

then press the OK Button. See Figure 46.

Figure 46 – Speaker Setup Menu Screen

Select “Automatic Setup-EzSet/EQ” and the screen shown in Figure 47

will appear to direct you to plug the EzSet/EQ microphone into the

Headphone Jack, and to set the level control on the subwoofer to the

halfway point.

Figure 47 – EzSet/EQ Screen

At any time, you may select Cancel to return to the Speaker Setup

menu without starting the EzSet/EQ process. When you are ready to

begin, select Continue and press the OK Button.

NOTE: Before running the EzSet/EQ process, the AVR 254 will

automatically set its master volume to -25dB.

Step Four – After you select “Continue”, the screen shown in Figure 48

will appear, directing you to select the number of speakers in your system.

Select 5.1 if no surround back speakers are present, or if the surround

back channels will be used for multizone operation.

Figure 48 – EzSet/EQ: Number of Speakers

NOTE: If you are using fewer than five main speakers in your

system, it will not be possible to configure your speakers using the

EzSet/EQ process; proceed as described in the Advanced Functions

section. If you have selected a 6.1-channel configuration, using only

a single surround back speaker, it is possible to use a combination

of EzSet/EQ automatic configuration for 5.1 speakers, connect the

single surround back speaker to the

left

Surround Back Speaker

Output, and then configure the surround back speaker manually, as

described in the Advanced Functions section. However, we do not

recommend the 6.1-channel configuration.

The test will begin, and the screen shown in Figure 49 will appear,

asking you to maintain silence during the EzSet/EQ configuration.

If possible, turn off any noisy appliances, such as air conditioners.

Avoid conversation. If unwanted sounds are inadvertently heard during

the test, such as a telephone, select Cancel to return to the Speaker

Setup menu.

Figure 49 – EzSet/EQ In Progress

As EzSet/EQ tests each speaker, its position will appear on screen.

Select Cancel to stop the test. If the test tone is heard from a different

speaker than the one indicated on screen, turn off the AVR and check

the speaker-wire connections, then turn the AVR back on and begin the

procedure again.

When the test is completed, the Continue option, will become available.

Select it, and a screen will appear, listing all of the speakers EzSet/EQ

detected, and offering three options:

• The Retest option reruns the EzSet/EQ process. Increasing the master

volume manually at this time may enable the EzSet/EQ process to

correctly detect some speakers.

• Selecting Cancel returns to the Speaker Setup menu.

• If the EzSet/EQ process detected the speakers correctly, select

Continue to proceed to the next test.

AVR254om.qxd 3/28/08 12:46 PM Page 34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info