Bedienungsanleitung Harman Kardon AVR254 (Seite 46 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ADVANCED FUNCTIONS

NOTE: All of the speaker setup submenus include the Exit and

Back options as shown at the bottom of Figure 58. To return

to a previous menu without making any changes, select Exit.

To save the current settings, select the Back option.

If you previously saved EzSet/EQ results in this setup position and you

wish to reconfigure the speakers from scratch, select the Reset option.

For best results, we recommend configuring the speakers in this order,

although it may differ from the order in which the submenus appear in

the Manual Speaker Setup menu: Number of Speakers, Crossover

(Size), Sub Mode, Distance and Level Adjust.

Number of Speakers

Move the cursor to the Number of Speakers line and press the Set

Button. See Figure 61.

Figure 61 – Number of Speakers Menu

The Number of Speakers menu lists each of the speaker groups.

Program the correct setting for each group: ON when the speakers are

present in the system, and OFF for positions where no speakers have

been installed. The Front Left & Right speakers are always ON and may

not be disabled. Any changes made to the system configuration will be

reflected in the total number of speakers displayed at the top of the

screen.

The setting for the surround back speakers includes a third option:

Zone 2. The AVR 254 is capable of multizone operation, allowing place-

ment of a pair of speakers in another room. Listeners in the remote room

may enjoy either the same program as in the main room or a different

source. The AVR 254’s assignable surround back amplifier channels make

multizone operation easier than ever, since an external power amplifier is

not required. Simply select the Zone 2 option at this line, and connect the

Surround Back Speaker Outputs to loudspeakers located in the remote

room. The main room will be configured automatically for up to 5.1

channels. See the Multizone Operation section for more information.

The settings in this menu affect a number of aspects of the AVR’s

operation, including the remainder of the speaker setup process and

the availability of various surround modes at any time.

When you have finished programming the number of speakers in the

system, select the Back option to insure the settings are saved correctly.

You may use the Back/Exit Button, and the settings will be saved.

Adjust Crossover Frequencies Menu

After you have programmed the number of speakers in the system, the

AVR will return to the Manual Speaker Setup menu, similar to the one

shown in Figure 46. Navigate to the Crossover (Size) line and press

the OK Button to display the Adjust Crossover Frequencies menu (see

Figure 62).

Figure 62 – Adjust Crossover Frequencies Menu

The AVR will only display those speaker groups which you programmed

in the Number of Speakers menu.

Refer back to Step One, where you determined each speaker’s

crossover. For the main speakers, this is the lowest frequency the

speaker reproduces well; and for the subwoofer, it’s the highest.

For each main speaker, select one of the seven crossover frequencies:

40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the crossover

frequency you determined in Step One is below 40Hz, select the first

option, “Large”. This setting doesn’t refer to the speaker’s physical size,

but to its frequency response, which is also called “full range”. This means

the speaker is capable of playing sounds throughout the frequency

spectrum, from the high pitches to the bass.

Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15 inches.

Make a note of each speaker group’s crossover setting in Table A3 in

the appendix.

When you have finished entering the settings, remember to select Back,

not Exit.

Sub Mode

Move the cursor to the Sub Mode line to program bass management

for the subwoofer. The subwoofer’s setting depends upon how you

programmed the front left and right speakers.

• If you set the front speakers to a numeric crossover frequency, the

subwoofer setting will be LFE, and you won’t be able to change it.

All low-frequency information will always be sent to the subwoofer.

If you don’t have a subwoofer, we recommend that you either

upgrade to full-range speakers or add a subwoofer to your system

at the earliest opportunity.

• If you set the front speakers to LARGE, you may select between

two possible settings for the subwoofer.

L/R+LFE: This setting sends all low-frequency information to

the subwoofer, including both information that would normally be

AVR254om.qxd 3/28/08 12:46 PM Page 46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info