Bedienungsanleitung Harman Kardon AVR260 (Seite 24 von 54) (Englisch)

502598

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

SYSTEM CONFIgURATION

Sub Mode

Move the cursor to the Sub Mode line to program bass management for the

subwoofer. The subwoofer’s setting depends upon how you programmed the

front left and right speakers.

If you set the front speakers to a numeric crossover frequency, the •

subwoofer setting will be LFE, and you won’t be able to change it.

All low-frequency information will always be sent to the subwoofer.

If you don’t have a subwoofer, we recommend that you either upgrade to full-

range speakers or add a subwoofer to your system at the earliest opportunity.

If you set the front speakers to LARGE, you may select from two possible •

settings for the subwoofer.

L/R+LFE: This setting sends all low-frequency information to the ■

subwoofer, including both information that would normally be

played through the front left and right speakers and the special low-

frequency effects (LFE) channel information.

LFE: This setting plays low-frequency information contained in the left ■

and right program channels to the front speakers, and directs only the

LFE channel information to the subwoofer.

NOTE

: The Speaker/Channel Indicators on the front panel of the receiver (see

Figure on page 31) will display the speaker size settings as follows.

For each speaker configured numerically, a single box will appear in the

position for that speaker. For each speaker configured as LARGE, a double

box will appear in its position. If a speaker is configured as OFF, no box will

appear. The subwoofer will be indicated by a single box, or no box if no

subwoofer has been configured. The letters inside the boxes appear when a

digital signal is being received that has that channel discretely encoded. The

letters flash when the signal is not present, such as when a DVD is paused.

A line will connect the SBL and SBR boxes when a 6.1-channel signal is

detected, indicating that the same signal is playing through both speakers.

Adjust Speaker Distance Menu

As explained above in Step Two – Measure Speaker Distances, sometimes the

speakers are placed at different distances from the listeningposition, which

can muddy the sound, as sounds are heard earlier or later than desired.

Even if all of your speakers are placed the same distance from the listening

position, do not skip this menu.

On the Manual Speaker Setup menu, move the cursor to the Distance line and

press the OK Button to display the Adjust Speaker Distance menu. See Figure

12.

Figure 12 – Adjust Speaker Distance

This menu requires you to enter the distance from each speaker to the

listening position, which you measured in Step Two – Measure Speaker

Distances and noted in Table A3 in the appendix.

The default unit of measurement is feet. If you wish to change the unit to

meters, press the Back/Exit Button until you return to the main AVR menu.

Scroll down to the System line, and select it to view the System Settings

menu. Scroll down this menu to the General AVR Settings section, and select

the Unit of Measure line. Press the OK Button to change the setting from Feet

to Meters.

Use the

Buttons to move the cursor to the Front Left line, press the OK

Button then use the

M N

Buttons to change the measurement as needed.

The values vary between 0 and 9 meters, with a default of 3 meters for all

speakers. Use the

M N

Buttons to move to each speaker in turn – Center,

Front Right, Surround Right, Surround Back Right, Surround Back Left,

Surround Left and Subwoofer, if present in your system.

NOTE

: When the multiroom system is in use, the surround back channels are

automatically assigned to the multiroom system, as mentioned earlier. You

will not be able to adjust the delay settings for these channels, and the cursor

will skip past them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR260 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR260

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info