Bedienungsanleitung Harman Kardon AVR260 (Seite 34 von 54) (Englisch)

502598

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

MULTIROOM OPERATION

When the Zone 2 menu appears, the blue cursor bar will be at the

Status:

Off

line. Since this line is used to turn the system on and off, do not make

an adjustment here unless you wish to turn the system on at this time. To

turn the system on, press the OK Button

once, to turn it off again, press

once more. If you do not wish to turn the system on at this time or to proceed

to the next step, press the

Button

once so that the blue cursor bar is

highlighting the

Source

line.

At the

Source

line, press the press the OK Button to cause the Source List to

slide in from the right. Use the

Button

to select the source.. When

the selection has been made, press the OK Button

to confirm your choice,

and continue to the

Volume

line by pressing the

Button

At the

Volume

line, press the

M N

buttons

or hold them pressed until

the desired volume level for the multi-room system is entered. DO NOT use

the regular volume control knobs for this setting.

Surround Amplifier Channel Assignment

The AVR is equipped with seven full-power amplifier channels to allow for

complete 7.1-channel operation without the need for additional external

amplifiers. However, in some installations you may wish to use the traditional

5.1-channel configuration for the main listening room, which allows the

surround back left/right amplifier channels to be used to power speakers

placed in a remote zone location.

If you wish to use the Surround Back channel amplifiers to power the remote

zone, you must change a setting in the multiroom setup menu. To make that

change, first call up the menu system by pressing the AVR Button

to bring

the main menu (Figure 1) to the screen. Next, press the

Button

until

the

Zone 2

menu line is highlighted in blue. Press the OK Button

enter the Zone 2 menu.

The Surround Back Amps line is used to assign the surround back channels

for multizone operation. Select the Zone 2 setting when multizone listening

is desired. If the multizone system is not in use, this setting may be changed

to Main Room to accommodate a 7.1-channel system. When the multiroom

system is turned off, this line will always display the MAIN setting. When the

multiroom system is turned on, this line will always display the MULTI setting,

reflecting that the surround back channels are always assigned to the remote

zone when the multiroom system is used.

Remember that once this setting is made you will not be able to take

advantage of any of the 6.1/7.1- channel decoding or processing modes, and

no Surround Back speakers must be selected in the speaker setup procedure

outlined earlier. In addition the speakers used for the remote zone must be

connected to the Surround Back/Multiroom Speaker Outputs

. The volume

for these speakers is set by the multiroom system, as explained above.

Multiroom Operation

To operate the multizone system using the remote, slide the Zone Select

Switch at the bottom of the remote to the “2” position. Press a Source Selector

to select a source input for the remote zone.

Adjusting the volume or mute controls will only affect the volume in the

remote zone. The on-screen menu functions will not be operative. The remote

will operate source devices that have been programmed into it as explained

in the Initial Setup section.

If the Remote IR Output jack

on the AVR is connected to an IR Input jack

on compatible Harman Kardon audio components such as CD, DVD or cassette

players, the transport functions of those machines may also be controlled

using the Transport Controls

on the remote control.

NOTE

: When the tuner is selected as the source for Zone 2, any change to

the frequency or preset will also change the station being listened to in the

main room, if the tuner is in use there. Similarly, if someone in the main room

changes the station, the change will also impact the remote room.

Although changes to the input source or Zone 2 volume will normally be

made using an IR sensor in the remote room that is connected to the AVR, it

is also possible to change those settings from the main listening room. This

is useful for situations where some or all of the remote rooms do not have an

IR sensor, or to take control over the remote room without actually being in

that room.

Once Zone 2 is turned on, it will remain on even if the AVR is placed in the

Standby mode in the main room by pressing the Power Off Button

the System Power Control

on the front panel. To turn off the multiroom

system from the main listening room, when the AVR is on, slide the Zone

Select Switch

on the Remote Control to Zone 2, and press the Off Button

Even when the AVR is turned off (to Standby mode) and the multiroom

system is turned off too, the multiroom system may be turned on at any time

by pressing the ON Button

while the Zone Select Button is set to Zone 2.

NOTE

: Only analog audio sources are available to the multizone system.

To hear digital devices, such as a CD player, in the remote zone, follow these

steps:

In addition to a digital audio connection, connect the source device’s 1.

analog audio outputs to any available analog audio inputs on the AVR,

noting in Table AA in the appendix which set of inputs was used.

In the Setup Source menu, leave the Audio Source setting at the digital 2.

audio input. However, scroll down to the Zone 2 Audio setting and select

the analog audio source used in step 1.

Harman Kardon AVR260 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR260

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info