Bedienungsanleitung Harman Kardon AVR354 (Seite 30 von 76) (Englisch)

502622

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Figure 32 – HDMI Monitor Output

Component Video: If the display does not have HDMI inputs, but

does have component video inputs, connect the Component Video

Monitor Outputs to the display (see Figure 33). As with HDMI connec-

tions, the AVR 354 is capable of converting composite and S-video

sources to the component video format, while upscaling the resolution to

as high as 1080i, depending on the display’s capabilities. Unlike HDMI

connections, component video connections do not enable the AVR 354

to detect the display’s capabilities and the appropriate resolution must

be selected manually, as described in the Initial Setup section.

Figure 33 – Component Video Monitor Outputs

Composite/S-Video: If the video display does not have HDMI or

component video inputs, connect the corresponding composite or

S-video Monitor Output to the display. If available, S-video is preferred

over composite video, and if used, the AVR 354 will convert composite

video sources to S-video. See Figure 34.

Figure 34 – Composite and S-Video Monitor Outputs

Consult the manual for your TV to make sure you understand how

to select the correct video input.

Step Six – Plug in AC Power

Having made all of your wiring connections, it is now time to plug each

component’s AC power cord into a working outlet.

You may plug one device into the AC Switched Accessory Outlet on the

rear of the AVR 354. See Figure 35. Make sure this device draws no

more than 50 watts. The device should have its mechanical or master

power switch turned on, and it will power on any time the AVR 354 is

turned on. If the device has a clock or must always be on, do not plug

it into this outlet.

Figure 35 – Switched AC Accessory Outlet

Before plugging the AVR 354’s AC Power Cord into an electrical outlet,

make sure that the Master Power Switch on the front panel is popped

out so that the word OFF appears on its top. Gently press the button to

turn the switch off. This will prevent the possibility of damaging the AVR

in case of a transient power surge.

The AVR 354 is equipped with a detachable power cord. It allows

you to fully wire your system before installing the AVR, which may be

required for some in-wall entertainment centers or custom applications.

The male end of the cord should be plugged into an unswitched AC

power outlet, and the female end should be plugged into the receptacle

on the AVR 354’s rear panel. See Figure 36.

Figure 36 – AC Power Input

Step Seven – Insert Batteries in Remote

The AVR 354 remote control uses four AAA batteries, which are included.

To remove the battery cover located on the back of the remote,

squeeze the tab and lift the cover.

Insert the batteries, as shown in Figure 37, making sure to observe

the correct polarity.

AVR 354

INSTALLATION

AVR354 OM.qxd 9/26/08 12:27 PM Page 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR354 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info