Bedienungsanleitung Harman Kardon AVR354 (Seite 31 von 76) (Englisch)

502622

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

Figure 37 – Remote Battery Compartment

When using the remote, remember to point the lens toward the front

panel of the AVR 354. Make sure no objects, such as furniture, are

blocking the remote’s path to the receiver. Bright lights, fluorescent lights

and plasma video displays may interfere with the remote’s functioning.

The remote has a range of about 20 feet, depending on the lighting

conditions. It may be used at an angle of up to 30 degrees to either

side of the AVR.

If the remote lights up when a button is pressed but the AVR does not

respond, check that the Zone Selector Switch at the bottom is in the

Zone 1 position.

If the remote seems to operate intermittently, or if pressing a button

on the remote does not cause the AVR Settings Button or one of the

Source Selectors to light up, then make sure the batteries have been

inserted correctly, or replace all four batteries with fresh ones.

Step Eight – Program Sources Into the Remote

The AVR 354 remote not only is capable of controlling the receiver,

but it may also be programmed to control many brands and models

of DVD players, cable boxes, satellite receivers, the Harman Kardon

DMC 1000 digital media center and TVs. It is also preprogrammed

to operate your iPod when docked in The Bridge II.

It may help to think of the remote as a book with pages. Each “page”

represents the button functions for a different device. To access the

functions for a particular device, first turn to its page; that is, switch

the remote’s device mode. Press the AVR Settings Button to access

the codes that control the receiver, or the Source Selector Buttons

to access the codes for the devices programmed into the remote.

The AVR 354’s remote control is factory-programmed to control many

Harman Kardon DVD players. If you have other source devices in your

system, follow these steps to program the correct codes into the remote.

1. Using the codes in Tables A14 – A24 of the Appendix, look up the

product type (e.g., DVD, cable TV box) and the brand name of your

source. The number(s) listed is/are potential candidates for the

correct code set for your particular device.

NOTE: The AUX Source Selector is used for the CD, HDTV, PVD

recorder, TiVo and VCR device types. Select the brand code

from the appendix table corresponding to the device and pro-

gram it into the AUX Source Selector. Similarly, the CBL/SAT

Source Selector is used for either a cable or satellite TV set-top

box. The first digit of the product code indicates the device type.

2. Turn on your source device.

3. This step places the remote in program mode. Referring to Figure

38, press and hold the Source Selector. The button will turn red, then

go dark. Continue holding it, and when it turns red again, release the

button; the remote is now in program mode. Follow the directions in

Step 4, below.

Figure 38 – Source Selectors

Optional: To reassign a device type from one Source Selector to another

Source Selector not being used (e.g., if there are two DVD players in

the system), press the Source Selector for the new device type now.

For example, to reassign the Cable/Sat Source Selector to operate a

DVD player, first press and hold the Cable/Sat Button, and then press

the DVD Button.

4. Enter a code from Step 1, above.

a) If the device turns off, press the Source Selector again to accept

the code; it will flash. The remote will exit Program mode.

b) If the device does not turn off, try entering another code. If you

run out of codes, you may search through all of the codes in the

remote’s library for that product type by pressing the

⁄

Button repeatedly until the device turns off. When the device turns

off, enter the code by pressing the Source Selector, which will

flash. The remote then exits Program mode.

5. Once you have programmed a code, it’s a good idea to try using

some other functions to control the device. Sometimes, manufacturers

use the same Power code for several different models, while other

codes will vary. You may wish to repeat this process until you’ve

programmed a satisfactory code set that operates most of the

functions you frequently use.

6. Find out which code number you have programmed by pressing

and holding the Source Selector to enter the Program mode. Then

press the OK Button, and the Source Selector will flash in the code

sequence. One flash represents “1”, two flashes for “2”, and so forth.

A series of many fast flashes represents “0”. Record the codes

programmed for each device in Table A9 in the appendix.

After you have programmed a code set to operate a device, test the

functions to see which ones may be missing or not operating correctly.

You may “learn” individual key codes if you have the device’s original

remote control by following this procedure:

AVR354 OM.qxd 9/26/08 12:27 PM Page 31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR354 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info