Bedienungsanleitung Harman Kardon AVR354 (Seite 33 von 76) (Englisch)

502622

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

IMPORTANT SAFETY NOTE: Installing a multizone system typi-

cally requires running various cables inside walls. Always comply

with the appropriate safety codes when installing concealed wiring.

The AVR 354’s multizone connections should be installed per the

requirements of all applicable state and local building codes, as

well as NEC (National Electrical Code) requirements. Failure to do

so may present a potential safety hazard. If you have any doubt

about your ability to work with electrical and telecommunications

wiring, you are advised to hire a licensed electrician or custom

installer to install the multizone system.

Multizone operation uses the Surround Back/Zone 2 amplifier channels,

whether you connect the remote speakers directly to the speaker outputs,

or if you connect an optional external amplifier to the preamp outputs. This

limits the system in the main listening room to 5.1 channels, which means

you cannot listen to 6.1- or 7.1-channel programs in the main room.

Select one or all three of these systems:

1. Connect an external amplifier to the Zone 2 Audio Outputs.

See Figure 42.

Figure 42 – Zone 2 Audio Outputs

It is recommended that you place the amplifier in the same room

as the AVR 354 so that a shorter length of interconnect cable is

used with a long run of speaker wire to the remote room, rather than

placing the amplifier in the remote room, which necessitates a long

run of interconnect cable that would be subject to signal degradation.

Depending on the number of channels available in your amplifier,

you may distribute the AVR 354’s analog audio signal to a single pair

of speakers for 2-channel listening, or to several pairs of speakers

located in different rooms.

The advantage of using the Zone 2 Audio Outputs is the ability

to have a 7.1-channel system in the main listening area at the same

time others are listening to a different source in the remote zone.

However, the benefit is achieved at the expense of purchasing an

additional component, i.e., the amplifier.

2. Connect the remote room’s speakers directly to the Surround

Back/Zone 2 Speaker Outputs. See Figure 43.

Figure 43 – Surround Back/Zone 2 Speaker Outputs

If you prefer not to purchase an external amplifier, you may reassign

the AVR 354’s Surround Back amplifier channels to power the

speakers. However, your main system will be limited to 5.1 channels,

which affects playback of discs and other programs recorded in 6.1

or 7.1 channels.

3. Connect an external amplifier to the Surround Back/Zone 2 Preamp

Outputs. See Figure 44.

Figure 44 – Surround Back/Zone 2 Preamp Outputs

This method also requires you to provide an additional amplifier. However,

this method may be used to increase the number of remote rooms in

the system when you are also using the Surround Back/Zone 2 Speaker

Outputs and the Zone 2 Audio Outputs.

In addition to the audio signal, you may connect an IR control device to

the AVR 354’s Zone IR Input so that listeners in the remote room may

turn the multizone system on or off, select a source input, control the

source device connected to that input and adjust the volume in the

remote zone.

NOTE: Only analog audio sources are available to the multizone

system.

Step Eleven – Turn On the AVR 354

Two steps are required the first time you turn on the AVR 354.

1. Gently press the Master Power Switch until the word OFF is no longer

visible. The Power Indicator above the two power switches should

light up in amber, indicating that the AVR is in Standby mode and is

ready to be turned on. See Figure 45. Normally, you may leave the

Master Power Switch in the ON position, even when the receiver is

not being used.

Figure 45 – Power Switches

2. There are several ways in which the AVR 354 may be turned on

from Standby mode.

a) Press the Standby/On Switch on the front panel. See Figure 45.

AVR 354

AVR354 OM.qxd 9/26/08 12:27 PM Page 33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR354 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info