Bedienungsanleitung Harman Kardon AVR645 (Seite 11 von 68) (Englisch)

502558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

MAIN REMOTE CONTROL FUNCTIONS 11

ENGLISH

Main Remote Control Functions

IMPORTANT NOTE: The AVR 645’s remote may

be programmed to control up to seven devices,

including the AVR. Before using the remote, it is

important to remember to press the Input

Selector button

that corresponds to the

unit you wish to operate. In addition, the AVR’s

remote is shipped from the factory to operate the

AVR and most Harman Kardon CD or DVD players

and cassette decks. The remote is also capable of

operating a wide variety of other products using

the control codes that are part of the remote or

by learning commands from other remotes. Before

using the remote with other products, follow the

instructions on pages 53-54 to program the

proper codes for the products in your system.

It is also important to remember that many of

the buttons on the remote take on different

functions, depending on the product selected

using the Input Selector Button

.The

descriptions shown here primarily detail the func-

tions of the remote when it is used to operate

the AVR.

Power Off Button: Press this button to

place the AVR or a selected device unit in the

Standby mode. Note that when the AVR is

switched off this will turn off the main room

functions, but if the Multiroom system is activated,

it will continue to function.

IR Transmitter Window: Point this window

towards the AVR when pressing buttons on the

remote to make certain that infrared commands

are properly received.

LCD Information Display: This two-line

screen displays various information depending on

the commands that have been entered into the

remote.

Power On Button: Press this button to turn

on the power to a device selected by pressing one

of the Input Selectors

(except Tape).

Input Selectors: Pressing one of these

buttons will perform three actions at the same

time. First, if the AVR is not turned on, this will

power up the unit. Next, it will select the source

shown on the button as the input to the AVR.

Finally, it will change the remote control so that

it controls the device selected.

The buttons labeled DVD, DMP and HDMI 1 are

each used to select either of two input sources:

• The first press of the DVD Button selects the

component connected to the DVD inputs. A sec-

ond press of this button selects the component

connected to the CD inputs.

• The first press of the button labeled DMP

selects The Bridge as the input. A second press of

this button selects the device connected to the

Tape inputs.

• The first press of the HDMI 1 button selects the

device that is connected to the HDMI 1 jack. A

second press selects the device connected to the

HDMI 2 jack.

In normal operation, the remote will revert to

controlling the AVR when no button is pressed

for 6 seconds. This allows the remote to automat-

ically return to control of important functions

such as volume, mute and surround mode selec-

tion after you have used the remote to control

another device. If you wish to change the length

of time that the remote operates another device,

or to have the remote remain active for control of

the other device (such as a DVD player or set-top

box) until you manually return control to the AVR

by pressing the AVR Selector

, follow the

instructions on page 40.

AVR Selector: Pressing this button will

switch the remote so that it will operate the AVR’s

functions. If the AVR is in the Standby mode, it will

also turn the AVR on.

AM/FM Tuner Select: Press this button to

select the AVR’s tuner as the listening choice.

Pressing this button when the tuner is in use will

select between the AM and FM bands.

6-Channel/8 Channel Direct Input:

Press this button to select the device connected

to the 6-Channel Direct Inputs or the

8-Channel Direct Inputs

(the input

available will depend on the selection 5.1 or

6.1/7.1 made in the surround mode setting,

see page 27 for more information).

Test Tone: Press this button to begin the

sequence used to calibrate the AVR’s output levels.

(See page 27 for more information on calibrating

the AVR.)

Sleep Button: Press this button to place

the unit in the Sleep mode. After the time shown

in the display, the AVR will automatically go into

the Standby mode. Each press of the button

changes the time until turn-off in the following

order:

Hold the button pressed for two seconds to turn

off the Sleep mode setting.

Note that this button is also used to change

channels on your TV, VCR and Sat receiver when

the appropriate source is selected, using the

device Input Selectors

Surround Mode Selector: Press this but-

ton to select any of the HALL, THEATER surround

modes. Note that depending on the type of

input, some modes are not always available. (See

page 33 for more information about surround

modes.) Note that this button is also used to

tune channels on your TV, VCR and Sat receiver

when the appropriate source is selected using

the device Input Selector

Night Mode: Press this button to activate

the Night mode. This mode is available only with

Dolby Digital encoded sources, and it preserves

dialog (center channel) intelligibilty at low vol-

ume levels (See page 23 for more information).

Channel Select Button: This button is

used to start the process of setting the AVR’s

output levels with an external source. Once this

button is pressed, use the

⁄

buttons

select the channel being adjusted, then press the

Set button

, followed by the

⁄

buttons

again, to change the level setting. (See page

40 for more information.)

Dim Button: Press this button to activate

the Dimmer function, which reduces the bright-

ness of the front-panel display, or turns it off

entirely. Press the button once to change the dis-

play to reduce the brightness by 50%, and press

it again within five seconds and the main display

will go completely dark. Note that this setting is

temporary; regardless of any changes, the display

will always return to full brightness when the

AVR is turned on. The blue illumination around

the Standby/On Button

will always remain

at full brightness regardless of the setting to

remind you that the AVR is still turned on. The

blue accent lighting inside the volume control

will also remain at full brightness when the panel

is at 50%, but go out when the panel lights are

fully dimmed.

min

OFF

29851_AVR645_ENG 30/10/06 9:46 Side 11

Harman Kardon AVR645 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info