Bedienungsanleitung Harman Kardon AVR645 (Seite 26 von 68) (Englisch)

502558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

26 SYSTEM CONFIGURATION

System Configuration

When the adjustment has been made, or if no

adjustment is required and all settings on this

page are complete, press the

⁄

Navigation

Button

F until the on-screen cursor is

pointing to

PAGE 1 and then press the

Set Button

Q to return to the main

IN/OUT SETUP menu to configure another

input, or if no further input configuration adjust-

ments are needed, press the

⁄

Navigation

Button

F until the on-screen cursor is

pointing to

MASTER MENU and then press

the Set Button

Q to return to the main

menu screen.

Video Monitor Settings

The VIDEO MONITOR SETTINGS

menu (Figure 10) is unique in that it contains a

mix of information display lines that detail status

information about the AVR 645’s video system

settings, along with a few lines where a specific

parameter may be changed. With the

MASTER

on the screen, press the

⁄

Navigation Button

F until the on-

screen cursor is pointing to

VIDEO

MONITOR SETTINGS

and then press the

Set Button

Q to move to the menu

screen.

Figure 10

The IN VIDEOFORMAT line is an informa-

tional display of the resolution of the incoming

video stream, and may not be adjusted.

The

IN VIDEO COPYPROT line is an

informational display that shows whether or not

an incoming video signal contains copy

protection encoding, and may not be adjusted.

The

VIDEO PROCESS line is an informa-

tional display of the setting made in the

IN/OUT SETUP menu indicating how

incoming video is processed for the input being

viewed, and may not be adjusted.

The

COMPONENT OUT line is an informa-

tional display of whether or not the Component

Video outputs are

ENABLED or OFF, based

on the input signal type and resolution, and

whether or not the incoming video signal has

HDCP content protection. It may not be adjusted.

The

S-VIDEO OUT line is an informational

display of whether or not the S-video outputs are

available at a 576i resolution (or OFF), based on

the input signal type and resolution and whether

or not the incoming video signal has HDCP

content protection. It may not be adjusted.

The

DISPLAY INTER line allows you to

choose between an

ANALOG video output

default value and an HDMI/DVI output by press-

ing the

‹

›

Navigation Button

F to

make the desired selection. When the setting is

ANALOG, the HDMI output is placed in a

Standby mode so that it automatically switches

to HDMI when an HDMI signal is detected. If a

high-definition input source is not HDCP-content-

protected, it may be output through the compo-

nent jacks; otherwise, it will be sent only to the

HDMI outputs. The

HDMI/DVI setting routes

all converted or processed video to the HDMI

outputs.

The HDMI AUDIO OUT line allows you to

choose whether a two-channel downmix of the

audio that accompanies the selected source is

sent over the HDMI connection (

YES) at the

maximum bit rate the display’s audio system is

capable of handling, or not (

NO). To change the

setting, press the

‹

›

Navigation Button

F to make the desired selection.

When required adjustments have been made for

this input, or if no adjustment is required, press

the

⁄

Navigation Button

F until

the on-screen cursor is pointing to

BACK TO

MASTER MENU

and then press Set Button

Q to return to the main menu screen.

Audio Setup

This menu allows you to configure the tone con-

trols. If you do not wish to change any of those

settings at this time, proceed to the next menu

screen. However, to make configuration changes

to those parameters, make certain that the

MASTER MENU is on the screen with the ➞

cursor pointing to the

AUDIO SETUP line,

and press the Set Button

Q.The

AUDIO SETUP menu (Figure 12) will appear.

Figure 12

The first line controls whether or not the

bass/treble tone controls are in the signal path.

The normal default is for them to be in-line, but if

you wish to remove them from the circuit for

“flat” response, first make certain that the ➞

cursor is pointing to the

TONE line on the

menu and press the

‹

›

Navigation Button

F so that OUT is highlighted in reverse

video.

If you wish to leave the tone controls in the sig-

nal path, the amount off boost or cut for bass

and treble may be adjusted by pressing the

⁄

Navigation Button

F so that the

➞ cursor is next to the line for the setting you

wish to adjust. Next, press the

‹

›

Navigation

Button

F until the desired setting is

shown.

When all desired changes have been made on

this menu, press the

⁄

Navigation Button

F so that the ➞ cursor is next to the

BACK TO MAIN MENUline and press

the Set Button

* AUDIO SETUP *

TONE :IN OUT

BASS :0

TREBLE :0

BACK TO MASTER MENU

→

*VIDEO MONITOR SETTINGS*

IN VIDEO FORMAT: 1080i

IN VIDEO COPY PROT: ON

VIDEO PROCESS: V CONVERS

COMPONENT OUT: OFF

S-VIDEO OUT: OFF

COMPOSITE OUT: OFF

DISPLAY INTER: HDMI/DVI

HDMI AUDIO OUT: NO

BACK TO MASTER MENU

→

29851_AVR645_ENG 30/10/06 9:46 Side 26

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR645 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info