Bedienungsanleitung Harman Kardon AVR645 (Seite 27 von 68) (Englisch)

502558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SYSTEM CONFIGURATION 27

ENGLISH

System Configuration

Surround Setup

The next step for that input is to set the surround

mode you wish to use with that input. Since sur-

round modes are a matter of personal taste, feel

free to select any mode you wish – you may

change it later. The Surround Mode chart on page

38 may help you select the mode best suited to

the input source selected. For example you may

select Dolby Pro Logic II or Logic 7 for most

analog inputs and Dolby Digital for inputs con-

nected to digital sources. In the case of inputs

such as a CD Player, Tape Deck or Tuner, you may

wish to set the mode to Stereo, if that is your

preferred listening mode for standard stereo

sources, where it is unlikely that sur

round encod-

ed material will be used. Alternatively, the 5

Channel Stereo or

Logic 7 Music mode may also

be a good choice for stereo-only source material.

It is easiest to complete the surround setup using

the full-OSD on-screen menus. From the

MASTER menu (Figure 7), press the

⁄

buttons

F until the ➝ cursor is next to the

SURROUND SELECT menu. Press the Set

Button

Q so that the SURROUND

SELECT

menu (Figure 13) is on the screen.

Figure 13

The first line on the menu allows you to select

the input for which the specific surround settings

will be applied. Press the

‹

›

Navigation

Buttons

F to select the input source to

be configured.

The

AUDIO IN-PORT and AUDIO IN

lines are for display only and may not be

changed through the

SURROUND SETUP

menu. The AUDIO IN-PORT displays the

physical connection source for the current active

input, and the

AUDIO IN line shows the

signal type present. Note that an

UNLOCK

message in the AUDIO IN line indicates that

a digital physical input source has been selected,

but that no data stream is present.

When the input selection has been made, press

the

⁄

Navigation Button

F to move

to the next configuration line.

The ADC SAMPLINGline is where you

determine whether the unit’s upsampling feature

is turned on or off.The default setting of 48kHz

puts the feature in a bypass, or “off,” mode and

will pass digital audio data through the DSP at

its native sample rate. To process incoming

44.1kHz signals at a higher resolution,

upsampled 96kHz sample rate, press the

‹

›

Navigation Buttons

F once so that

96kHz is highlighted.

When the desired setting has been made, or if no

adjustment is required at this line, press the

⁄

Navigation Button

F to move to

the next configuration line.

The

SURR MODE and SELECT lines are

related, as they guide you to the choice of the

surround mode that will be activated whenever

the input being configured is selected.

At the

SURR MODE line, press the

‹

›

Navigation Buttons

F to select the sur-

round mode group (such as Dolby modes, DTS

modes, Logic 7 modes, and DSP or Stereo modes)

that is applicable to the input source. After mak-

ing a selection, press the

⁄

Navigation

Button

F to move to the SELECT line.

At the

SELECT line, you are able to choose

the specific mode to be used from within the

major surround mode group. The choice of modes

is governed by the input type (as some modes

such as Dolby Digital or DTS-ES are not available

for analog sources), as well as by the speaker

configuration, since some modes are only

available when a full 7.1 speaker complement is

present. The full list of available modes is

detailed in the surround mode chart on page 38.

In addition, you may also use the settings in the

SURROUND CONFIG menus to delete

modes you do not normally use from the

available choices.

When both a surround mode group and a

specific surround mode have been selected, press

the

⁄

Navigation Button

F to move

to the next configuration line.

The

DEFAULT SURR mode line is where you

choose the mode that is activated when a digital

source is selected. The factory default setting of

LAST will activate the last-used mode for any

digital source. If you prefer to always have a digi-

tal source switch to the specific mode encoded

by digital data flags in the incoming audio data

stream, press the

‹

›

Navigation Buttons

F so that ORIGINAL appears.

Before proceeding to the

SURROUND

CONFIG

line, it is worth noting that the set-

tings in the submenus attached to that line may

require a considerable amount of time to com-

plete. Although they are useful in that they allow

you to customize the list of surround modes that

appear in normal use of the AVR, you may wish

to bypass those settings at this time so that you

may complete the configuration process. You may

return to this menu line at a later time, once you

have had a chance to listen to the various sur-

round modes and determine which you want to

“keep” and which you do not want to use. The

settings in this line are not primary controls and

do not impact the way the AVR “sounds.”

To proceed to the

SURROUND CONFIG

line, press the

⁄

Navigation Button

F to move to that line; otherwise, press it

again to move to the

DOLBY SURR

SETUP

line and skip to the instructions for

that setting.

The

SURROUND CONFIG line is your

gateway to a broad range of surround mode

configurations. To continue, press the Set

Button

Q to go to the main

SURROUND CONFIG menu (Figure 14).

Figure 14

The LOGIC 7 GLOBAL line is the only item

on this menu page that is menu-specific, and it

allows you to select whether or not Logic 7 will

be the default surround mode for any incoming

audio signal. The default setting is

OFF, which

chooses the native mode. Press the

‹

›

Navigation Buttons

F so that ON

appears, to activate the global Logic 7 setting for

this input.

The remaining five items in this menu are global

settings that take you to a submenu listing the

individual surround modes available within the

selected mode group. To select a surround mode

list, press the

⁄

Navigation Button

F until the on-screen cursor is pointing to

the desired mode, and then press the Set

Button

Q. Within each menu, press the

⁄

Navigation Button

F to move the

cursor up and down through the list, and then

press the

‹

›

Navigation Buttons

F to

turn the mode “ON” or “OFF.”

** SURROUND CONFIG **

LOGIC 7 GLOBAL:OFF

DOLBY MULTI CONFIG

DOLBY 2.0 CONFIG

DTS CONFIG

PCM 44.1/48kHz CONFIG

PCM 96k CONFIG

BACK TO SURROUND CONFIG

➔

** SURROUND SETUP **

SOURCE: VIDEO 1

AUDIO IN PORT: ANALOG

AUDIO IN: PCM 44.1kHz

ADC SAMPLING: 48K 96K

SURR MODE: LOGIC 7

SURR SELECT: MUSIC 5.1

DEFAULT SURR: LAST

SURROUND CONFIG

DOLBY SURR SETUP

BACK TO MASTER MENU

➔

29851_AVR645_ENG 30/10/06 9:46 Side 27

Harman Kardon AVR645 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info