Bedienungsanleitung Harman Kardon AVR645 (Seite 41 von 68) (Englisch)

502558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

OPERATION 41

ENGLISH

Note that when the 6-Channel or 8-Channel

Input is in use, you may not select a surround

mode, as the external decoder determines the

processing in use. In addition, there is no signal

at the record outputs or bass management when

the 6-Channel or 8-Channel Direct Input is in use

and the tone or balance controls will not

function.

Controls and Use of Headphones

• Adjust the volume to a comfortable level using

the front panel Volume Control

or remote

Volume Up/Down

I buttons.

• To temporarily silence all speaker outputs press

the Mute button

K. This will interrupt the

output to all speakers and the headphone jack,

but it will not affect any recording or dubbing

that may be in progress. When the system is

muted, the word

MUTE will blink in the Main

Information Display

. Press the Mute

button

K again to return to normal

operation.

• During a listening session you may wish to

adjust the Bass Control and Treble Control to

suit your listening tastes or room acoustics. Note

that these controls (and Balance) will not

function when the 6/8 channel direct input is in

use.

• To set the output of the AVR so that the output

is “flat,” with the tone and balance controls

deactivated, press the Tone Mode button

once or twice so that the words Tone

Out

appear momentarily in the Main

Information Display

. To return the tone

controls to an active condition, press the Tone

Mode

button once or twice so that the

words

Tone In momentarily appear in the

Main Information Display

• When the tone controls are active, the amount

of bass and treble boost/cut may be adjusted by

first pressing the Tone Mode Button on the

front panel

or the remote

two or three

times until the desired setting (

BASS MODE

or TREBLE MODE) appears in the on-screen

display and the Lower Display Line

. Next,

use the

⁄

Navigation Button

on the

remote or the

‹

›

Button on the front panel

to change the setting as desired. The unit

will return to normal operation within five

seconds after the setting is changed.

• For private listening, plug the 6.3 mm stereo

phone plug from a pair of stereo headphones

into the front panel Headphone Jack

Note that when the headphone’s plug is con-

nected, the speakers will automatically mute and

a two-channel stereo signal will be sent to the

headphones. The Lower Display Line

will

read

DOLBY H: BP, indicating that the

headphone output is in the Bypass mode, and to

confirm that no processing is being used.

• When the headphones are in use, you may take

advantage of the Dolby Headphone modes to

bring added spaciousness to headphone listen-

ing. Press the Dolby Mode Select Button

or the Surround Mode Group Selector

cycle through the three Dolby Headphone modes

to select the one that you prefer.

Surround Mode Selection

One of the most important features of the AVR is

its ability to reproduce a full multichannel

surround sound field from digital sources, analog

matrix surround encoded programs and standard

stereo or even mono programs.

Selection of a surround mode is based on personal

taste, as well as the type of program source

material being used. For example, CDs, motion

pictures or TV programs bearing the logo of one of

the major surround-encoding processes, such as

Dolby Surround should be played in either the

Dolby Pro Logic II Movie (with movies) or Music

(with music) surround mode, with any DTS NEO:6

mode or with Harman Kardon´s exclusive Logic 7

Movie Mode, to create a full range 5.1 channel

or (with Logic 7 and DTS NEO:6) even 7.1

channel surround signal from surround encoded

programs, with a stereophonic left and right rear

signal, just as it was recorded (e.g. sound being

recorded from left rear side will be heard from

that side only, for more details see chart on page

38).

When no rear speakers are in use, the Dolby 3

Stereo mode should be selected with all surround

recordings.

Note that when Dolby Digital 2.0 signals (e.g.

"D.D. 2.0" tracks from DVD), that are encoded

with Dolby Pro Logic information, are received

via any digital input, the Dolby Pro Logic II Movie

mode will be selected automatically (in addition

to the Dolby Digital mode) and will decode a full

range 5.1 channel surround sound even from

those recordings (see also "Dolby Digital" on

page 42).

To create wide, enveloping sound field

environments and defined pans and flyovers with

all analog stereo recordings select the Dolby Pro

Logic II Music or Emulation mode or

Harman Kardon’s exclusive Logic 7 Music mode

for a dramatic improvement in comparison to the

Dolby Pro Logic (I) mode of former times.

NOTE: Once a program has been encoded with

matrix surround information, it retains the

surround information as long as the program is

broadcast in stereo. Thus, movies with surround

sound may be decoded via any of the analog

surround modes such as Pro Logic II Cinema,

Logic 7 Cinema or DTS Neo:6 Cinema, when they

are broadcast via conventional TV stations, cable,

pay-TV and satellite transmission. In addition, a

growing number of made-for-television programs,

sports broadcasts, radio dramas and music CDs

are also recorded in surround sound. You may

view a list of these programs at the Dolby

Laboratories Web site at www.dolby.com.

Even when a program is not listed as carrying

intentional surround information, you may find

that the Dolby Pro Logic II, Dolby Pro Logic IIx,

DTS NEO:6 Music or Logic 7 Music or Enhanced

modes often deliver enveloping surround presen-

tations through the use of the natural surround

information present in all stereo recordings.

However, for stereo programs without any

surround information the Theater, Hall and 5/7CH

Stereo modes should be tried (effective particularly

with old ”extreme” stereo recordings) and for

mono programs, we suggest that you try the

Theater or Hall modes.

Surround modes are selected using either the

front panel controls or the remote. To select a

new surround mode from the front panel, first

press the Surround Mode Group Selector

Button

until the desired major surround

mode group such as Dolby, DTS or Logic 7 is

selected. Next, press the Surround Mode

Selector Button

to choose the specific

individual surround mode.

To select a surround mode using the remote

control, press the button for the major surround

mode group that includes the mode you wish to

choose from: Dolby

, DTS Surround

DTS Neo:6

, Logic 7

, Stereo

DSP Surround

. The first press of the button

will show the current mode from that group if it

is already in use, or the first available mode if you

are currently using another mode. To cycle

through the available modes in that group press

the button again until the desired mode appears

in the Lower Display Line

and the on-

screen display.

To select from the DSP modes (Hall 1, Hall 2,

Theater) press the Surround Mode Selector

repeatedly to scroll through the list of

available modes.

Operation

29851_AVR645_ENG 30/10/06 9:46 Side 41

Harman Kardon AVR645 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info