INSTALLATION AND CONNECTIONS 15
INSTALLATION AND CONNECTIONS
System Installation
After unpacking the unit, locating it in a place with ade-
quate vantilation and placing it on a solid surface capable
of supporting its weight, you will need to make the con-
nections to your audio and video equipment.
IMPORT ANT NOTE: For your personal safety and to
avoid possible damage to your equipment and speakers ,
it is always good practice to turn off and unplug the A VR
and ALL source equipment from the AC output before
making any audio or video system connections .
Audio Equipment Connections
We recommend that you use high-quality interconnect
cables when making connections to source equipment
and recorders to preserve the integrity of the signals .
1. Connect the analog output of a CD player to the
CD Audio Inputs .
NOTE: When the CD player has both fixed and vari-
able audio outputs , it is best to use the fixed output
unless you find that the input to the receiver is so low
that the sound is noisy , or so high that it is distorted.
2. Connect the analog Play/Out jacks of a cassette
deck, MD , CD-R or other audio recorder to the
Tape Input Jacks i. Connect the analog
Record/In jacks on the recorder to the Ta p e
Output Jacks k on the AVR 7200.
3. Connect the output of any digital sources such as
such as a CD or DVD changer or player , advanced
video game , a digital satellite receiver , HDTV tuner
or digital cable set-top box or the output of a
compatible computer sound card to the
Optical
and Coaxial Digital Audio Inputs j &(.
4. Connect the coaxial or optical Digital Audio Outputs
fh on the rear panel of the A VR to the matching
digital input connections on a CD-R or MiniDisc
recorder .
5. Assemble the AM loop antenna supplied with the unit
so that the tabs at the bottom of the antenna loop
snap into the holes in the base . Connect it to the
AM
and GND Screw T erminals ‚.
6. Connect the supplied FM antenna to the
FM (75-
ohm) Connection • . The FM antenna may be an
external roof antenna, an inside powered or wire-
lead antenna or a connection from a cable TV sys-
tem. If the antenna or connection uses 300-ohm
twin-lead cable , you must use an optional 300- to
75-ohm adapter to make the connection.
7. Connect the front, center , surround and surround
back speaker outputs ¡£bc to the respective
speakers . If only one speaker is used for the sur-
round back channel, it may be connected to either
the
SBL or SBR T erminal ¡.
To ensure that all the audio signals are carried to your
speakers without loss of clarity or resolution, we sug-
gest that you use high-quality speaker cable . Many
brands of cable are available and the choice of cable
may be influenced by the distance between your
speakers and the receiver , the type of speakers you
use , personal preferences and other factors .
Regardless of the brand of cable selected, we recom-
mend that you use a cable constructed of
multistrand
copper with a gauge of 14 or smaller .
Remember that
in specifying cable , the lower the number , the thicker
the cable .
Cable with a gauge of 16 may be used for runs of less
than ten feet. W e do not recommend that you use
cables with an AWG of 18 or higher , due to the power
loss and degradation in performance that may occur .
Cables that are run inside walls should be marked to
indicate listing with UL, CSA or other appropriate test-
ing agency standards . Questions about running cables
inside walls should be referred to an installer or a
licensed electrician who is familiar with the NEC and/or
the applicable local building codes in your area.
When connecting wires to the speakers , be certain to
observe proper polarity . Note that the positive (+) ter-
minal of each speaker connection has a specific color
code as noted on page 8. However , most speakers
still use a red terminal for the positive (+) connection.
Connect the “negative” wire to the black terminal on
both the receiver and the speaker .
NOTE: While most speaker manufacturers adhere to
an industry convention of using black terminals for
negative and red ones for positive , some may vary
from this configuration. T o ensure proper phase and
optimal performance , consult the identification plate on
your speaker or the speaker’s manual to verify polarity .
If you do not know the polarity of your speaker , ask
your dealer for advice before proceeding , or consult
the speaker’s manufacturer .
We also recommend that the length of cable used
to connect speaker pairs be identical. For example ,
use the same length piece of cable to connect the
front-left and front-right or surround-left and sur-
round-right speakers , even if the speakers are a dif-
ferent distance from the AVR 7200.
8. Connections to a subwoofer are normally made via
a line-level audio connection from the
Subwoofer
Output › to the line-level input of a powered
subwoofer . When a passive subwoofer is used, the
connection first goes to a power amplifier , which will
be connected to one or more subwoofer speakers .
If you are using a powered subwoofer that does not
have line-level input connections , follow the instruc-
tions furnished with the speaker for connection
information.
9. If an external multichannel audio source with
5.1 outputs such as an external digital processor/
decoder , DVD-Audio or SACD player is used,
connect the outputs of that device to the
8-
Channel Direct Inputs .
Video Equipment Connections
Video equipment is connected in the same manner as
audio components . Again, the use of high-quality inter-
connect cables is recommended to preserve signal
quality .
Although the outputs from any compatible video
device may be connected to any video input, to sim-
plify programming device codes into the remote con-
trol, we recommend that a hard-drive recorder product
such as a TiVo
®
or ReplayTV
®
be connected to the
Video 1 Connectors ⁄ . If there is no hard
-drive
recorder in your system, connect the VCR to those
connectors; otherwise connect it to the
Video 2
Connectors ¢ª
. The audio outputs of your TV
should be connected to the
Video 2 Inputs ª
, and
the outputs of a cable box or satellite receiver to the
Video 3 Inputs ™.
Note that the AVR 7200 will not convert signals from
composite to S-Video , or vice versa. S-Video inputs may
only be viewed when the AVR 7200 is connected to a
TV set or video display with S-Video capability . If you use
both standard composite video and S-Video sources in
your system, it is important that you connect both an
S-Video cable and a standard composite video cable
(a coax cable with an RCA plug on both ends) between
the AVR 7200 and your TV or projector . Consult the
instructions for your TV set or projector for more infor -
mation on connecting both types of signals .
1. Connect a VCR’s or other video source’s audio and
video Play/Out jacks to the
Video 1/Video 2 Input
Jacks
ª on the rear panel. The Audio and
Video Record/In jacks on the VCR should be con-
nected to the
Video 1/Video 2 Output Jacks
¢⁄ on the AVR 7200.
2. Connect the analog audio and video outputs of
a satellite receiver , cable TV converter or television
set or any other video source to the
Video 3 Input
Jacks
™.
33
33
34
32
31
AVR 7200 OM 1/27/03 4:46 PM Page 15