Bedienungsanleitung Harman Kardon AVR7300 (Seite 43 von 60) (Englisch)

502638

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ADVANCED FEATURES 43

ADVANCED FEATURES

To adjust the on-screen appearance of the semi-OSD

system, press the OSD Button U to bring the

MASTER MENU to the screen. Press the

Navigation Button o, until the on-screen ➔

cursor is next to the ADVANCED line. Press the

Set Button q to enter the ADVANCED

SELECT menu (Figure 19).

When the ADVANCED SELECT menu

(Figure 19) appears, press the

⁄

Navigation

Button o so that the on-screen ➔ cursor is point-

ing to the SEMI OSD/TIME OUT line.

Select one of these options:

• To keep the semi-OSD system activated, but to

adjust the length of time the displays remain on the

screen, press the

‹

›

Navigation Button o

until the desired time-out is shown. The default

setting is 5 seconds.

• To turn the semi-OSD system off so that it does not

appear at any time, press the

‹

›

Navigation

Button o so that OFF is shown on the right

side of the line.

If you wish to make other adjustments, press the

⁄

Navigation Button o until the on-screen ➔

cursor is next to the desired setting or the BACK

TO MASTER MENU line and press the Set

Button q. If you have no other adjustments to

make, press the OSD Button U to exit the

menu system.

Full-OSD Time-Out Adjustment

The FULL OSD menu system is used to simplify

the setup and adjustment of the AVR 7300 by using a

series of on-screen menus. The factory default setting

for these menus leaves them on the screen for 20

seconds after a period of inactivity before they disap-

pear from the screen (Time-Out). Time-Out is a safety

measure to prevent image retention of the menu text

in your monitor or projector, which might happen if the

menus were left on indefinitely. However, you may

prefer a different time period before the on-screen

display disappears.

To change the full-OSD Time-Out, you will need

to make an adjustment in the ADVANCED

SELECT menu (Figure 19). To start the adjust-

ment, press the OSD Button U to bring the

MASTER MENU to the screen. Press the

Navigation Button o, until the on-screen ➔

cursor is next to the ADVANCED line. Press the

Set Button q to enter the ADVANCED

SELECT menu (Figure 19).

At the ADVANCED SELECT menu (Fig. 19)

make certain that the on-screen ➔ cursor is next to

the FULL OSD TIME OUT line by pressing

the

⁄

Navigation Button o as needed. Next,

press the

‹

›

Navigation Button o until the

desired time is displayed in seconds. Unlike most of

the other options in this menu, this is a permanent

setting change, and the Time-Out entry will remain in

effect until it is changed, even if the unit is turned off.

If you wish to make other adjustments, press the

⁄

Navigation Button o until the on-screen

➔ cursor is next to the desired setting or the

BACK TO MASTER MENU line and press

the Set Button q. If you have no other adjust-

ments to make, press the OSD Button U to exit

the menu system.

AVR7300(120v)-OM 6/14/04 9:15 AM Page 43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR7300 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info