Bedienungsanleitung Harman Kardon AVR7300 (Seite 45 von 60) (Englisch)

502638

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

MULTIROOM OPERATION

MULTIROOM OPERATION 45

Once this setting is made, you may press the

⁄

Navigation Button o to make any of the other

adjustments available on this menu. If no other adjust-

ments are needed, press the OSD Button U to exit

the menu system.

Multiroom Operation

When operating the AVR 7300 from a remote room

location where an IR sensor link has been connected

to the AVR 7300’s rear-panel Multiroom IR Input

B, you may use either the main remote control or

the Zone II remote. To turn on the multiroom feed,

press the AVR Selector e

∫

to turn the unit

on to the last source, or any of the other Selector

Buttons

ç∂

dXi to turn on to a

specific source.

As long as an IR feed to the AVR 7300 has been

established from the remote room, using any of the

buttons on either remote will control the remote loca-

tion volume r

, change the tuner frequency

, change the tuner preset v

or mute

the output W

If the Remote IR Output Jack C on the AVR 7300

is connected to an IR Input jack on compatible

Harman Kardon audio components such as CD, DVD

or cassette players, the transport functions of those

machines may also be controlled using the Transport

Controls tu

ƒ©˙∆

on either

remote control.

To turn the system off from the remote room, press

the Power Off Button a

. Remember that the

AVR 7300 may be turned on or off from the remote

room, regardless of the system’s operation or status in

the main room.

NOTE: When the tuner is selected as the source for

the remote zone, any change to the frequency or pre-

set will also change the station being listened to in the

main room, if the tuner is in use there. Similarly, if

someone in the main room changes the station, the

change will also have an impact on the remote room.

To turn on the Multiroom system from the main listen-

ing room, press the Multiroom Button

on the

remote. When the MULTI ON/OFF message

appears in the on-screen display and the Lower

Display Line $, press the Set Button q and

then press the

⁄

Navigation Button o so

the display changes to MULTI ON. Press the

Set Button q again to activate the setting. Note

that this method may be used to turn the Multiroom

system on or off even when the AVR is in the Standby

mode in the main listening room.

When the Multiroom system is turned on, the input

selected using the Multiroom menu will be fed to the

Multiroom Audio and Video Outputs Oø on the

rear panel as well as the A-BUS Connector L. The

volume will be as set in the previous selection, although

it may also be adjusted using an optional IR sensor and

the Zone II remote in the remote location, or the A-BUS

keypad, or on the optional audio power amplifier con-

nected to the Multiroom Audio Outputs ø.

Although changes to the input source or remote room

volume will normally be made using an IR sensor in

the remote room that is connected to the AVR, it is

also possible to change those settings from the main

listening room. This is useful for situations where some

or all of the remote rooms do not have an IR sensor,

or to take control over the remote room without actu-

ally being in that room.

In addition to using the MULTI-ROOM

SETUP menu, as shown on the previous page, you

may change the source or volume in the remote zone

using the remote. Press the Multiroom Button `

on the remote, and when the MULTI ON/OFF

message appears in the on-screen display and the

Lower Display Line $, press the Set Button q

and then press the

⁄

Navigation Button o to

toggle past that message to MULTI LEVEL

or MULTI INPUT.

To change the remote room’s input source, when

MULTI INPUT appears, press the Set Button

q, and then press the

⁄

Navigation Button

o until the desired input appears in the on-screen

display and in the Lower Display Line $.

To change the remote room’s volume, when

MULTI LEVEL appears, press the Set Button

q, and press the

⁄

Navigation Button o

to change the volume setting. Note that this volume

adjustment controls the level for the output to the

Multiroom Audio Outputs

and for any speakers

connected to the Surround Back/Multiroom

Speaker Outputs

when the Surround Back

amplifier channels are configured for Multiroom use,

as shown on page 44. This adjustment does NOT

change the volume level for any room where an

A-BUS module is used, as that setting is only

adjustable using the A-BUS module’s volume

control or built-in IR sensor.

Once the Multiroom system is turned on, it will remain

on even if the AVR 7300 is placed in the Standby

mode in the main room by pressing the Power Off

Button

or the Main Power Switch A on the

front panel.

The Multiroom system will remain on even if the

unit is turned off in the main room. In that event,

although front-panel indicators and the accent

lighting around the volume control will turn off, a

MULTI-ROOM ON message will remain in

the Lower Display Line $ to remind you that

power is still applied to the unit, and that it is being

used for Multiroom operation elsewhere in the house.

Remember that if you turn the unit completely off by

pressing the Main Power Switch , the feed to

the second zone will also be turned off.

When the AVR 7300 is turned off in the main room,

the Multiroom system may be turned on at any time

by pressing the Multiroom Button `, or any of the

Selector Buttons

∫ç∂

in the remote room.

NOTES ON MULTIROOM OPERATION:

• The Zone II remote does not contain a button for

the Front-Panel Video 5 Input , but you may

select that source for the Multiroom system using

the MULTI-ROOM SETUP menu or an

optional remote that has been programmed with the

code for the Video 5 button from the AVR’s main

remote control.

• In addition to the Zone II remote supplied with your

AVR, you may use the main remote control or any

remote programmed with Harman Kardon codes.

Note, however, that only the remote codes applica-

ble to the remote room system or the operation of

source devices will function. Buttons used to change

other “Main Room” listening functions such as sur-

round mode changes will not work with the multi-

room system.

AVR7300(120v)-OM 6/14/04 9:15 AM Page 45

Harman Kardon AVR7300 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info