502638

Harman Kardon AVR7300 Seite 48

48
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
48 CONFIGURING THE REMOTE
CONFIGURING THE REMOTE
commands from another device’s remote into the
AVR remote.
Figure 32
3. The SELECT A DEVICE message will appear
in the LCD display (Figure 23). Press the
⁄
/
¤
Navigation Buttons o to scroll through the list
of device categories and press the Set Button
q when the device for which you wish to set
the codes appears. For this example, we will
select “TV” to enter the codes needed to
operate your TV.
4. The next menu screen (Figure 33) will prompt you
to select the button, or “key,” on the AVR remote
that you wish to program. Press that button on
the AVR remote.
Figure 33
5. Once you press the button to be programmed on
the AVR remote, press and hold the button on the
remote control for the device to be programmed
within five seconds, as instructed on the next
menu screen (Figure 34).
Figure 34
6. Continue to hold the button on the original remote
until the menu on the AVR remote’s LCD screen
changes. If the code is successfully learned, you will
see the display shown in Figure 35.
Figure 35
If you see that menu, proceed to Step 9. If the code
is
not
successfully learned, you will see the display
shown in Figure 36. If that menu appears, proceed
to Steps 7 and 8.
Figure 36
7. If the message shown in Figure 36 appears in
the display, press the Set Button q to try pro-
gramming the button again. When the remote
prompts you to press and hold the key on the
original remote again by showing the display
shown in Figure 34, immediately press the button
on the source remote again. To avoid another
failed attempt, make certain that the windows on
the two remotes are facing one another.
8. Continue to hold the button on the original remote
until the LCD display changes again. If the code
was successfully learned, you will see the display
shown in Figure 35. In that case, go to Step 9.
If the LEARN FAILED display (Figure 36)
appears again, you may either try to program the
key again, or press the
⁄
Navigation Button
o to stop the process. It is possible that some
remotes may use code sequences or infrared fre-
quencies that are not compatible with the AVR
remote, and those codes cannot be learned.
When the display shown in Figure 37 appears,
press the Set Button q to exit the Learning
system.
Figure 37
9. When a code has been learned successfully, you
have three options. When the display shown in
Figure 35 is on the LCD screen on the AVR
remote, you may press the Set Button q to
learn additional codes from the buttons on a
source remote into the AVR remote. Follow Steps
4 through 6 as often as needed to complete the
code-learning process.
10. If you wish to change the name that appears in
the LCD display when the button that has just
had a new code learned is pressed, press the
⁄
Navigation Button o so that the display
shown in Figure 38 appears in the LCD display.
Press the Set Button q to be taken to a
RENAME KEY display. Enter the new name for
the key following the instructions shown in the
Renaming Individual Keys section of this manual
on page 54. If you find it more convenient to
rename the buttons at a later time, you may do
that separately by following the instructions on
page 53.
Figure 38
11. When you have programmed all keys for the
desired device, press the
⁄
Navigation
Button o twice when the LEARN MENU
(Figure 35) appears so that you see the display
shown in Figure 39. Press the Set Button q
to return the remote to normal operation.
Figure 39
12. If you wish to program the codes for another
device, repeat the procedure outline above, but
select a different device in Step 3.
Changing Devices
In the factory default settings, the AVR remote is
programmed so that the commands transmitted
correspond to the device selected by pressing one
of the Input Selectors
3
. This is logical, as you
want the remote to control the device you have selected.
However, in some circumstances you may have con-
figured your system so that the devices connected
to the AVR 7300 do not correspond to the default
device settings and the legends printed on the remote.
For example, if your system has two VCRs you may
connect the second VCR to the VID 2 input. There is
no problem in doing that, but in normal operation the
commands issued after selecting the VID 2 input are
for a television, not a VCR.
The AVR remote allows you to correct that situation
through the “Changing Devices” process. This enables
you to assign the codes from one type of device to
a different button. For example, in the steps below,
we will explain how to program the VID 2 buttons to
provide the commands to operate a VCR. Of course,
you may program the remote to have any of the
devices take on the code set of any other device, as
your system requires. And, with the AVR remote’s
“Rename” function, you can even change the way
the name of the device appears on the remote’s LCD
display so that you see exactly which commands are
being sent.
To program the buttons normally assigned to one
device for the commands of another, follow these
steps:
1. Press and hold the Program Button
O
for
about three seconds while the message shown
in Figure 21 appears in the remote’s LCD
Information Display
2
. Release the button
when the red light under the Set Button q
appears.
2. The remote’s MAIN MENU message (Figure
21), will appear in the LCD display and the Set
Button q will remain illuminated in red. Press
the
⁄
Navigation Button o twice so that
CHANGE DEVICE appears on the bottom line
of the LCD screen, as shown in Figure 40. Press
the Set Button q to begin the process of
reassigning the commands used for a particular
device.
Figure 40
3. The next menu display is where you select the
Input Select, or device, that you wish to change.
When the display shown in Figure 41 appears,
press the
⁄
/
¤
Navigation Button o to scroll
through the list to find the device you wish to use
for another function. In this case we will select
MAIN MENU
CHANGE DEVICE
LEARN MENU
END LEARNING
LEARN MENU
RENAME KEY
LEARN FAILED
EXIT
LEARN FAILED
RETRY
LEARN MENU
LRN ANOTHER KEY
PRESS KEY ON
ORIGINAL REMOTE
SELECT A KEY
TO PROGRAM
MAIN MENU
LEARN
AVR7300(120v)-OM 6/14/04 9:15 AM Page 48
… 48 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Harman Kardon AVR7300 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info