Bedienungsanleitung Harman Kardon AVR7300 (Seite 53 von 60) (Englisch)

502638

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

CONFIGURING THE REMOTE 53

CONFIGURING THE REMOTE

3. At the next menu screen (Figure 71) press the

⁄

Navigation Buttons o once so that

ZSET DISABLE appears in the lower line of

the LCD display.

Figure 71

4. Within five seconds, press the Set Button

disable the SPL Select Button j. Once the

Set Button

is pressed, the word EXITING

will flash four times in the lower line of the LCD

display and then it will return to normal operation.

Once these steps are completed, when the SPL

Select Button j is pressed, the remote will show

ZSET DISABLE and it will not be activated.

To restore the EzSet feature to normal operation,

repeat the procedure outlined above, except that in

Step 3 you should press the

⁄

Navigation

Button o so that E

ZSET ENABLE appears in the

lower line of the LCD display. When that display

appears, press the Set Button

and the EzSet

feature will be reactivated. You may then press the

Clear Button

to exit the remote’s menu system

and return to normal operation or press the Set

Button

again to immediately use the EzSet

feature to calibrate the system as shown on

pages 29–30.

Renaming

While the names given to the buttons and inputs on

the remote represent recognizable categories of

audio/video products, system operation may be easier

if the displays shown in the remote’s LCD screen are

customized to reflect the specific characteristics of a

playback source’s brand name or the new function

given to a specific button when one remote’s controls

are programmed into the AVR remote. The AVR

remote allows you to change the name of either a

master device or any button on the remote using the

following steps.

Renaming a Device

To rename a specific device/input source button, fol-

low these steps. For this example, we will show you

how to rename the Device/Input Selector normally

shown as “TV” to “HDTV TUNER.”

1. Press and hold the Program Button

for

about three seconds while the message shown

in Figure 16 appears in the remote’s LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

The remote’s MAIN MENU message (Figure 20),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button o until RENAME

appears on the bottom line of the LCD screen, as

shown in Figure 72.

Figure 72

3. At the next menu screen press the

⁄

Navigation Button o until RENAME

DEVICE appears on the bottom line of the

LCD screen, as shown in Figure 73. Press the

Set Button

to begin renaming a device.

Figure 73

4. The next display screen (Figure 74) is where you

select the device that will be renamed. In our

example, that is the TV button. Press the

⁄

Navigation Button o until the name of the

base device appears and then press the Set

Button

Figure 74

5. At the next menu screen, you will see the device

name on the bottom line of the display with a

blinking cursor box to the right of the device

name. Press the

‹

Navigation Button o to

return the blinking cursor to the far left side of the

display line. You may then retitle the device name

as shown in the next step.

6. To enter the new name, press the Numeric Keys

. The letters above the numbered buttons

indicate which letter or symbol will appear when

the button is pressed during the renaming

process. The first press of the button will enter the

first letter shown, subsequent presses of the same

button will change the display to the other letters

above that numbered key. For example, since the

first letter we need to rename the input to HDTV

Tuner is an “H,” you would locate the “H” above

the “4” button, and press the button twice. The

first press shows a “G,” the second press changes

it to an “H.” Consult the table at the end of this

section to see which characters pressing a partic-

ular button generates.

7. After you enter the first letter of the new device

name, there are three options for entering the next

character:

a. To enter a letter that requires a different

numeric key to be pressed, simply press that

button. The cursor will automatically move to

the next position and the first letter accessed

by the new button will appear. Following our

example, the next letter needed is a “D,” so

you would press the “3” button once.

b. To enter a letter that uses the same numeric

key, you must first press the

›

Navigation

Button

to move the blinking cursor block

to the next position. Then press the Numeric

Key

as required to enter the desired letter.

To enter a blank space, press the

›

Navigation

Button

twice. The first press will move the

cursor to the right, and the second press will

move the cursor one more space to the right,

leaving a blank space between the last letter

and the next one.

8. Repeat Step 7 as needed to enter all the needed

letters, numbers, characters and spaces.

9. When the text entry is complete, press the

Set Button

. The LCD display will blink

DEVICE RENAMED three times and then

return to normal operation.

Once a device is renamed you will see the new name

on the top line of the remote’s LCD display whenever

the Input//Device Selector

is pressed, or when

any other command/function button on the remote is

pressed after the main Device Selector is pressed.

Note that renaming a device in the remote will

not

change the name of the input used by the on-screen

menu system of the AVR 7300.

NOTES ON RENAMING DEVICES:

• To move the cursor to the right or left of the display

during the renaming process, press the

‹

›

Navigation Buttons

as required.

• The table below shows the letters, numbers and

characters that may be accessed by pressing the

Numeric Keys:

Key Characters Key Characters

1 [,],/,1 6 M,N,O,6

2 A,B,C,2 7 P,Q,R,S,7

3 D,E,F,3 8 T,U,V,8

4 G,H,I,4 9 W,X,Y,Z,9

5 J,K,L,5 0 -,.,#,0

• Renaming a device changes the name of the device

only, not any of the individual key functions within

that device memory. To change the name of an

individual device, follow the instructions in the next

section.

RENAME DEVICE

RENAME

RENAME DEVICE

MAIN MENU

RENAME

SET SPKR LEVELS

Z S ET DISABLE

AVR7300(120v)-OM 6/14/04 9:16 AM Page 53

Harman Kardon AVR7300 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info