Bedienungsanleitung Harman Kardon BDS 375 -SET (Seite 14 von 38) (Englisch)

537901

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

BDS Preparing the Remote Control

4. Aim the remote towards the component you just turned on and enter a set-up code

number from Step 1, above. Use the Program (Red) button for the ﬁrst digit; the

Bookmark (Green) button for the second digital; the Thumbnail (Yellow) button for the

third digit; and the Zoom (Blue) button for the last digit. If the code to be entered is

“0” you do not need to press the corresponding button; for numbers “1” and above,

press the button that number of times. When you have entered all four digits, press

the OK button – the component should now turn off.

5. If the remote control turns the component off in Step 4, press the Aux button once

again to store the set-up code number. To conﬁrm that the code has been saved, the

LED indicator will blink three times.

Auto Search Method

If you have tried all of the four digit set-up code numbers listed for your device and it still

did not turn off, you should use the following Auto Search Method.

1. Turn on the device you would like the BDS remote to control, either manually or with

its own remote control.

2. Press and hold down the Aux device button for three seconds; the BDS remote will

enter set-up mode. NOTE: The remote will remain in the programming mode for 20

seconds; you must perform Step 3 within that time.

3. Select the region you are located in and the type of device that you are programming:

For a US TV, do not press any of Program (Red), Bookmark (Green), Thumbnail

(Yellow) or Zoom (Blue) buttons.

• For an EU TV, press the Program (Red) button one (1) time.

• For an HDTV, press the Program (Red) button two (2) times.

• For a US cable tuner, press the Program (Red) button three (3) times.

• For an EU cable tuner, press the Program (Red) button four (4) times.

• For a US satellite tuner, press the Program (Red) button ﬁve (5) times.

• For an EU satellite tuner, press the Program (Red) button six (6) times.

4. Point the BDS remote control toward the device and press the Cursor Up button;

each button press sends a “Power” signal for one set-up code number. Continuing

to press the Cursor Up button will produce a quick scanning of the set-up code

numbers. Release the Cursor Up button as soon as the device turns off. If you go past

the correct set-up code number, you can return to it by pressing the Cursor Down

button, one code number at a time, until the device turns back on.

5. If the BDS remote control turns the component off in Step 4, press the Aux Button

once again to store the set-up code number. To conﬁrm that the code has been

saved, the LED indicator will blink three times.

Programming Individual Button Codes on the Remote:

You can program codes from other component remotes onto the BDS remote’s buttons

that are shown shaded in the following illustration:

1. Press and simultaneously hold down the Aux and the Program (Red) buttons on the

BDS remote control for at least three seconds. The remote’s Aux button will blink

once.

2. Place the BDS receiver remote and the remote from which you want it to learn codes

head-to-head about 1 inch (2.5cm) apart, with their IR transmitter windows facing

one other.

3. Press the button on the BDS remote to which you want to teach a command. (The

remote will remain in the learning mode for 20 seconds after the button is pushed.)

4. Press the button on the other remote that you want to “teach” to the BDS remote.

When the IR code has been received and stored, the Aux button’s LED will ﬂash three

times, and the BDS receiver remote will remain in the learning mode, ready to learn

another code. If no IR code is received within 20 seconds, the Aux LED will ﬂash

rapidly several times, and the remote will exit the learning mode.

5. Repeat Step 3 and Step 4 for each command you want to teach the BDS receiver

remote. NOTE: If the Aux button’s LED goes out at any time, you will need to begin

again from Step 2. until it blinks three times.

6. Press the Aux button once, or wait for 20 seconds to cancel learning program mode.

NOTE: Any previously stored setup code will be erased when program mode is

activated.

Channel Control “Punch Through” Commands

After programming the remote to control an auxiliary (Aux) component, you can also

program it to control the Aux component’s channel up/down and transport functions

(Play, Pause, etc.) even when the remote is not in the Aux control mode. For example, if

the remote is programmed to operate your TV in the Aux control mode, you can also have

the TV’s channel +/– functions “punch through” and operate even when the remote is in

the Disc, Radio or USB control modes, for example. (NOTE: When this feature is active,

TV or satellite channel +/– functions will override any existing channel controls set to

that mode.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon BDS 375 -SET Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon BDS 375 -SET

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info