Bedienungsanleitung Harman Kardon HD990 (Seite 8 von 16) (Englisch)

502536

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

HD 990

Installation

To prevent possible damage to your speakers and other components in your audio

system, it is important that ALL components, including the HD 990 and your receiver or

preamp and ampliﬁers, are turned off and unplugged from their AC power source when

installing any new component.

Connecting the HD 990 to your audio system is simple. Using standard RCA-to-RCA

interconnect cords or balanced XLR-cables, connect the left and right Audio Output

jacks 1 on the rear panel to the CD input jacks on your receiver, surround processor

or preampliﬁer.

If your system includes an optional external digital-to-analog converter, or if you are using

a receiver or other processor that has the capability to decode PCM digital input signals,

connect the Coaxial or Optical Digital Output jack  to the Coaxial or Optical Digital input

on the decoder. Make certain to use a coaxial-style interconnect cable, as standard audio

cables will not perform as well.

If you use the matching Harman Kardon HK 990 ampliﬁer, you may connect it to the HD 990

with the special HRS-Link cable, which transmits both audio and clock-synchronization

signals. This very advanced connection rewards you with ultimate sound quality. Simply

connect the HRS-Link Output 6 on the HD 990 to the HRS-Link Input on the HK 990.

If you have additional external audio sources, you might want to connect their coaxial or

optical digital output to the Coaxial or Optical Digital Inputs 5 on the rear panel of the CD

player. This will enable you to use the audiophile high-grade digital-to-analog converters

and processing power in the HD 990 rather than the (older and less powerful) converters

of your external source.

Note that to hear the sound from the external source when connected like this, the input

of your ampliﬁer or receiver should be the one to which the HD 990 is connected.

Install two AA batteries by turning the remote over so that you are holding the bottom

side up. Press lightly on the embossed arrow on the cover and gently slide the cover

toward you in the direction of the arrow. Insert the batteries inside the compartment,

being careful to follow the + and – polarity indications at the bottom of the compartment.

Replace the cover by placing it on the remote and sliding it back toward the top of the

remote.

NOTE:

When replacing batteries, always replace both at the same time. When the unit

will not be used for an extended period of time, it is also a good idea to remove the

batteries so that the potential for corrosion or damage is avoided.

If the HD 990 is installed behind a cabinet or other obstruction that may block the path

between the front-panel

Remote Sensor

and the location of the remote, an optional

external IR sensor may be used. Connect the sensor to the

Remote IR-In Jack

2 on the

rear panel. This jack may also be connected to the IR output jack of another compatible

Harman Kardon component or a compatible IR-system remote product.

You may also use the IR Sensor in the HD 990 to send commands to other compatible

remote-controlled products. Connect the

Remote IR-Out Jack

3 to the input of the

other product or system.

Connect the power to a nonswitched AC wall outlet or to the accessory outlet on the rear

of another audio device in your system, and you are ready to go!

NOTE:

When using the accessory outlet on another product to power the HD 990, make

certain that it has the compatibility to power a device that draws at least 20 watts of

current in addition to being able to handle the requirements of the other devices that may

be plugged into the accessory outlets. If you use a “switched” outlet, it is important to

remember that the host product must be turned on for the HD 990 to operate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HD990 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HD990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info