Bedienungsanleitung Harman Kardon HK 3385 (Seite 17 von 28) (Englisch)

502808

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

You are now ready to connect your various components to your receiver.

Before beginning, make sure that all components, including the HK 3385,

are turned completely off and their power cords are unplugged. Don’t

plug any of the power cords back in until you have finished

making all of your connections.

Remember that your receiver generates heat while it is on. Select a

location that leaves several inches of space on all sides of the receiver. It

is preferable to avoid completely enclosing the receiver inside a cabinet.

It is also preferable to stack components on separate shelves rather

than directly on top of the receiver. Some surface finishes are delicate.

Try to select a location with a sturdy surface finish.

Step One – Connect the Speakers

If you have not yet done so, place your speakers in the listening room

as described in the Speaker Placement section.

Connect the front left and right loudspeakers to the Speaker 1 speaker

terminals on the HK 3385. Remember to maintain the proper polarity by

always connecting the positive and negative terminals on each speaker

to the positive and negative terminals on the receiver. If you wish to

place a second pair of speakers in another room, or in the same room

for additional sound power, connect those speakers to the Speaker 2

Outputs, again remembering to maintain polarity. You may use the

Speaker 1/2 Selector on the front panel or remote to activate either

or both pairs of speakers simultaneously. See Figure 9.

Figure 9 – Speaker Connections

Step Two – Connect the Subwoofer

Connect the Subwoofer Outputs on the HK 3385 to the line-level inputs

on your subwoofer. The same full-range signal is output through both jacks.

Thus, you have the option of connecting each jack to the line-level input

on a separate subwoofer. If you have only one subwoofer with a single

line-level input, connect it to the right Subwoofer Output on the HK 3385.

See Figure 10. Consult the manufacturer’s guide for the subwoofer for

additional information.

Figure 10 – Subwoofer Connection

Step Three – Connect the Antennas

Connect the FM and AM antennas to their terminals. See Figure 11.

Figure 11 – Antenna Connections

Step Four – Connect the Source Components

Use the worksheets in the Appendix to note which connections you will

use for each of your source devices.

For each source, select a source input (Video 1, Video 2, Video 3, etc.).

In Table 2 we recommend connecting certain types of sources to certain

source inputs to make it easier to use the remote control.

The remote is preprogrammed to operate certain Harman Kardon

components as shown in Table 2. However, you may connect any

component with analog audio and/or composite video outputs to

any source input on the HK 3385, with the exception of the Phono

Inputs, and you may use the original remote control supplied with

the component. It is not possible to reprogram the HK 3385 remote,

or to change the device type associated with any source input.

HK 3385

SUB

Right (Spkr 1) Right (Spkr 2) Left (Spkr 1)Left (Spkr 2)

HK 3385

INSTALLATION

HK 3385 OM 4/13/07 12:02 PM Page 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HK 3385 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info