Bedienungsanleitung Harman Kardon HKTS 5 (Seite 3 von 10) (Englisch)

534545

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

HKTS 5

HKTS 160SUB Rear-Panel Connections

Crossover control: This knob adjusts the subwoofer's cutoff between 50Hz and 150Hz.

The higher you set the Crossover control, the higher in frequency the subwoofer will

operate and the more its bass will "overlap" that of the system's other speakers. This

adjustment helps achieve a smooth transition of bass frequencies between the subwoofer

and the system's other speakers for a variety of different rooms and subwoofer locations.

NOTE: If you have connected the subwoofer to a receiver/processor with a low-pass

ﬁltered LFE output, set the subwoofer's Crossover control to the 150Hz positon (fully

clockwise).

Phase switch: The Phase switch determines whether the HKTS 160SUB’s piston-like

action moves in and out in phase with the satellite speakers. If the subwoofer were

to play out of phase with the satellite speakers, the sound waves produced by the

subwoofer could be canceled out, reducing bass performance and sonic impact. This

phenomenon depends in part on the relative placement of all the speakers in the room.

In most cases the Phase switch should be left in the "NORMAL" position. However, it

does no harm to experiment, and you can leave the Phase switch in the position that

maximizes bass response and impact.

Power On Mode switch: If this switch is set in the"AUTO" position and the Power switch

is set to "ON", the HKTS 160SUB will automatically turn itself on when it receives an

audio signal and will enter the standby mode once no audio signal has been received for

about 15 minutes. When this switch is set in the "ON" position, the HKTS 160SUB will

remain on whether or not it is receiving an audio signal. An LED on the HKTS 160SUB’s

top panel indicates whether the subwoofer is in the on or standby state:

•

When the LED glows white, the HKTS 160SUB is turned on.

•

When the LED is not illuminated, the HKTS 160SUB is in standby mode.

When the Power switch is set to "OFF", the LED will not be illuminated, no matter what

setting the Power On Mode switch is in.

Subwoofer Level control: Use this control to adjust the HKTS 160SUB’s volume. Turn

clockwise to increase the volume; turn counterclockwise to decrease the volume.

Line-Level In/LFE connector : Connect the subwoofer output of your receiver or preamp/

processor to this jack. The signal from this connector passes through the subwoofer's

internal low-pass crossover.

Power switch: Set this switch in the "ON" position to turn the HKTS 160SUB on. The

subwoofer will then either be on or in standby mode, depending on the setting of the

Power On Mode switch.

Power cord (non-detachable): After you have made and veriﬁed all subwoofer and

speaker connections described in this manual, plug this cord into an active, unswitched

electrical outlet for proper operation of the HKTS 160SUB. DO NOT plug this cord into the

accessory outlets found in some audio components.

HKTS 160SUB Rear-Panel Connections

Crossover control

Phase switch

Power On Mode switch

Subwoofer Level control

Line-Level LFE connector

Power switch

Power cord

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 5 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HKTS 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info