Bedienungsanleitung Harman Kardon HKTS 5 (Seite 5 von 10) (Englisch)

534545

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

HKTS 5

Mounting Options

3. Bring the speaker cable through the wall-bracket attachment plate, and mount the

attachment plate on the wall in the desired location.

Bring Speaker Cable

Through Opening

4. Thread the speaker cable through the arc-shaped opening on the top of the mounting

bracket, not the screw hole.

Cable to

Speaker

Cable from

Wall Plate

Side View

Overhead View

Bring Speaker Cable

Through Arc-Shaped

Opening

5. Attach the mounting bracket to the wall plate by inserting the tab at the top of the

attachment plate into the slot on top of the bracket and snapping the bracket onto

the attachment plate.

Insert Tab into Slot

and Snap Bracket

onto Plate

Feed Cable Through

Mount and out of

Opening

6. Fit the terminal cover onto the bracket as shown in the illustration below, then

connect the speaker leads to the terminals on the underside of the speaker.

Remember to observe the correct polarity.

Terminal Cover

Mounting Bracket

Side View

Connect Cable Leads

to Speaker Terminals

7. Fit the terminal cover into the opening on the underside of the speaker so that it is

ﬂush against the speaker and covers the terminals. Insert the supplied long bracket

bolt up through the bottom of the bracket and terminal cover, and screw it into the

threaded insert on the underside of the speaker. The bolt should be snug but not so

tight as to prevent the speaker from pivoting on the bracket.

Fit Terminal Cover

into Recess on

Speaker Bottom

Attach Speaker

to Bracket Using

Long Bolt

You can pivot the wall-mounted speaker from side to side; however, attempting to tilt it

up or down will damage the bracket and possibly the wall, which would not be covered

by your warranty.

Wall-Mounting the Center Speaker

1. Determine the location for the speaker. If possible, position the speaker so that one

of the mounting screws (not included; use size #10) can be installed directly into a

wall stud. If that is not possible, use optional wall anchors that are rated to support

at least 25 lb (11.3kg) and are appropriate for the construction and materials of your

wall. The customer is responsible for the proper selection and use of mounting

hardware, available through hardware stores, to wall-mount the speaker

properly and safely.

2. Bring the speaker cable through the wall-bracket attachment plate as shown, and

mount the attachment plate on the wall in the desired location.

Use Mounting Hardware Appropriate

for Wall Construction and Materials

Bring Cable Through

Opening

3. Remove the rubber pads from the foot rests on the bottom of the center speaker

and connect the speaker leads to the terminals on the underside of the speaker.

Remember to observe the correct polarity.

4. Use the supplied screws to attach the speaker to the wall-mount bracket. The screws

thread into the center foot-rest openings that were exposed when you removed the

rubber pads in the previous step.

Use Supplied Screws

to Attach Speaker to

Bracket

Thread Screws into

Center Openings

Connect

Cable

Remove Pads

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 5 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HKTS 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info