Bedienungsanleitung Harman Kardon HKTS 65BQ (Seite 7 von 12) (Englisch)

534543

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

HKTS 65BQ

Speaker Mounting Options (cont.),

and Wall-Mounting: Center Speaker

8. Connect the speaker wire to the speaker terminals as shown in the illustration:

–

A) Push Down on Cap

to Open Hole

B) Insert Bare Wire

into Open Hole

C) Release Cap

to Secure Wire

Insert the conductor with the colored band into the speaker’s red (+) terminal, and insert

the other conductor into the speaker’s black (–) terminal.

IMPORTANT: Make sure the (+) and (–) bare wires do not touch each other or the other

terminal. Touching wires can cause a short circuit that can damage your receiver or

amplier.

9. Slide the speaker portion of the wall-mount bracket onto the speaker as shown in the

illustration. Fit the grooves on the bracket onto the rails in the speaker, and apply even

pressure on both sides of the bracket so it slides straight onto the speaker.

Fit Bracket Grooves

Onto Speaker Rails

Push Down Evenly On

Both Sides of Bracket

• Pull any slack speaker wire back through the bracket as you slide the bracket onto

the speaker.

• Push the bracket all the way onto the speaker until it snaps into place.

10. Slide the speaker onto the bracket’s wall section, as shown in the illustration. Pull any

slack speaker wire back through the bracket’s wall section.

Slide Speaker

Onto Bracket

Wall Section

11. Fit the metal stop plate into the recess on the bottom of the bracket with the pad

facing the bracket, and fasten it to the bracket using two of the supplied screws. It

will prevent the speaker from detaching from the bracket and will hold the speaker’s

position as you rotate it.

Wall-Mounting: Center Speaker

1. Determine the location for the speaker.

2. Attach the center speaker wall-mount bracket to the wall using hardware that is

appropriate for the wall’s construction and materials. Attach the anchors through the

holes shown in the illustration.

Use These

Holes to Attach

Bracket to Wall

NOTE: The center speaker weighs 3.3 lb (1.5kg). Be sure to use hardware that can

support this weight.

CAUTION: Before making speaker connections, be sure that your receiver or

amplier is turned OFF and its AC cord is unplugged from the AC power source.

3. Connect the speaker wire to the speaker terminals as shown in the illustration:

–

A) Push Down on Cap

to Open Hole

B) Insert Bare Wire

into Open Hole

C) Release Cap

to Secure Wire

Insert the conductor with the green colored band into the speaker’s red (+) terminal, and

insert the other conductor into the speaker’s black (–) terminal.

IMPORTANT: Make sure the (+) and (–) bare wires do not touch each other or the other

terminal. Touching wires can cause a short circuit that can damage your receiver or

amplier.

4. Using two of the supplied screws, attach the center speaker to the bracket, as shown

in the illustration.

Wall-Mount

Bracket

Supplied

Screws

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 65BQ Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info