Bedienungsanleitung Harman Kardon HKTS 65BQ (Seite 10 von 12) (Englisch)

534543

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

HKTS 65BQ

Operating Your Subwoofer (cont.),

and Specifications

Wireless Operation

When the wireless transmitter receives an audio signal from the source, it will immediately

turn on and its status LED will change to ashing green or solid green:

Green (ashing): Transmitter is on but has not established a link with the wireless

subwoofer

Green (solid): Transmitter is on and has already established a link with the wireless

subwoofer.

Red: Standby (no signal detected, transmitter off)

The transmitter will automatically enter the Standby mode after no audio signal is

detected from the source for approximately 10 minutes.

Wireless Code Settings

The Wireless Code selectors on the transmitter unit and subwoofer must be set to the

same position for the system to function correctly.

In the unlikely event that there is interference when operating the system, or if you

have more than one HKTS 220SUB operating, you may change the channel at which the

system operates. Set the Wireless Code selectors on one subwoofer’s transmitter module

and subwoofer to one of the other three positions.

You can also set up a maximum of two subwoofers to receive audio from a single

transmitter by setting the Wireless Code selectors on the transmitter and both of the

subwoofers to the same position.

Subwoofer Adjustments

Volume

Use the Subwoofer Level Control to set the subwoofer’s volume. Turn the knob clockwise

to increase the subwoofer’s volume; turn the knob counterclockwise to decrease the

subwoofer’s volume.

Notes on Setting Subwoofer Volume:

Sometimes the ideal subwoofer volume setting for music is too loud for lms, while the

ideal setting for lms is too quiet for music. When setting the subwoofer volume, listen to

both music and lms with strong bass content and nd a “middle ground” volume level

that works for both.

If your subwoofer always seems too loud or too quiet, you may want to place it in a

different location. See Speaker Placement: Subwoofer, on page 5, for more information.

Phase

The Phase switch determines whether the subwoofer’s piston-like action moves in and

out in phase with the satellite speakers. If the subwoofer were to play out of phase with

the satellite speakers, the sound waves from the satellites could cancel out sound waves

from the subwoofer, reducing bass performance and sonic impact. This phenomenon

depends in part on the placement of all the speakers in the room.

Although in most cases the Phase switch should be left in the “Normal” position, there

is no absolutely correct setting for the Phase switch. When the subwoofer is properly in

phase with the satellite speakers, the audio will be clearer, have maximum impact and

make percussive sounds like drums, piano and plucked strings sound more lifelike. The

best way to set the Phase switch is to listen to music that you know well and set the

switch in the position that gives drums and other percussive sounds maximum impact.

Bass Boost

When set to the “On” position, the Bass Boost switch enhances low-frequency

performance, resulting in bass with more impact, which you may prefer while watching

movies or listening to music. There is no harm in experimenting with this control. Setting

the switch to the “Off” position will return normal low-frequency performance to your

system.

Specifications

HKTS 65 System

Frequency response: 45Hz – 20kHz (–6dB)

SAT-TS60 Satellite Speakers

Midrange transducers: Dual 3" (75mm) honeycomb at-diaphragm

drivers, video-shielded

High-frequency transducer: 1" (25mm) CMMD

Lite dome, video-shielded

Suggested amplier power range: 20 – 150 watts

Nominal impedance: 8 ohms

Sensitivity (2.83V/1m): 83dB

Enclosure type: Sealed

Dimensions (H x W x D): 11-25/32" x 4-11/32" x 3-15/32"

(299mm x 110mm x 88mm), including stands

Weight: 3.4 lb (1.55kg)

CEN-TS60 Center Speaker

Midrange transducers: Dual 3" (75mm) honeycomb at-diaphragm

drivers, video-shielded

High-frequency transducer: 1" (25mm) CMMD Lite dome, video-shielded

Suggested amplier power range: 20 – 150 watts

Nominal impedance: 8 ohms

Sensitivity (2.83V/1m): 83dB

Enclosure type: Sealed

Dimensions (H x W x D): 4-11/32" x 10-11/32" x 3-15/32"

(110mm x 272mm x 88mm), including stands

Weight: 3.3 lb (1.5kg)

HKTS220SUB Wireless Subwoofer

Low-frequency transducer: 8" (200mm) down-ring cone

Amplier power: 200 watts (continuous), 400 watts (peak)

Frequency response: 45Hz – 200Hz (–6dB)

Controls: Volume, phase, bass boost

Connections: LFE (RCA-type); left and right line-level (RCA-

type)

Enclosure type: Sealed

External trigger input voltage: 3 – 30 volts, AC or DC

Subwoofer power requirement: 120V, 60Hz (USA); 220V – 240V, 50/60Hz (EU)

Subwoofer power consumption: <0.5W (standby); 243W (maximum, 120V);

261W (maximum, 230V)

Subwoofer dimensions

(H x W x D):

13-29/32" x 10-1/2" x 10-1/2"

(353mm x 267mm x 267mm)

Subwoofer weight: 19.8 lb (9kg)

Transmitter power requirement: 100 – 240V AC, 50/60Hz

Transmitter power consumption: <0.5W

Transmitter unit dimensions

(H x W x D):

1-3/8" x 5" x 3-1/2"

(35mm x 127mm x 89mm)

Transmitter unit weight: 0.26 lb (117g)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 65BQ Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info