Bedienungsanleitung Harman Kardon RCP 7 (Seite 10 von 24) (Englisch)

456600

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

PROGRAMMING SOURCES

Programming Sources

The RCP 7 remote is capable of controlling not only the receiver and

DVD player included in your CP system, but it may also be programmed

to control many brands and models of VCRs, CD players, cable boxes,

satellite receivers, cassette decks and TVs, as well as an iPod device

(not included) docked in Harman Kardon’s optional The Bridge.

It may help to think of the remote as a book with pages. Each page

represents the button functions for a different device. In order to access

the functions for a particular device, you first need to turn to that page,

that is, switch the remote to that device mode. This is done by pressing

the AVR Button to access the codes that control the receiver, or the

Input Selectors to access the codes for the devices programmed into

the remote.

You may have noticed that three of the Input Selectors look different

from the others (see Figure 2). For the DVD/CD, TAPE/The Bridge and

HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is

printed on the button, and a secondary source, whose name is printed

above the button.

When the remote is in the device mode for the primary source (e.g.,

DVD) pressing the device selector will cause it to light in red. When the

remote is in the secondary source’s device mode, the selector will light

in green when pressed.

To switch between the primary and secondary device modes, press the

selector twice quickly in succession. The selector will retain this selection

until the next time you toggle between the primary and secondary

device modes. That is, if you press the DVD/CD Selector twice quickly

so that the CD source is activated, then press another source selector,

such as Video 1, the next time you press the DVD/CD Selector, the

remote will return to the CD device mode.

The RCP 7 remote is factory-programmed to control the AVR 347, the

DVD 48 and an iPod docked in The Bridge. If you have other source

devices in your system, such as a VCR, or a cable or satellite television

set-top box, follow these steps to program the correct codes into

the remote:

1. Using the codes in Tables A2–A9 of the Appendix, look up the

product type (e.g., cable TV box) and the brand name of your source.

The number(s) listed are potential candidates for the correct code set

for your particular device.

2. Turn on your source device.

3. This step places the remote in Program mode and varies slightly,

depending on which Input Selector is being programmed. Refer to

Figure 2.

a) DVD, Tape, Video 1, Video 2, Video 3 and Video 4 Sources:

Press and hold the Input Selector until the Program Indicator LED

starts to flash, then release it. Follow the directions in Step 4.

b) CD Source: Press the DVD/CD Input Selector twice quickly so

that it turns green. Then press and hold it until the selector relights

and the Program LED flashes. Follow the directions in Step 4.

c) HDMI 1 Source: Press and hold the Input Selector until the

Program Indicator flashes, then release it. Next, press the Input

Selector that corresponds to the device type you want to program

into the HDMI 1 mode, i.e., DVD, VCR or CBL/SAT. Then follow

the directions in Step 4.

d) HDMI 2 Source: Press and release the Input Selector once,

quickly press the Input Selector again so that it turns green, then

release it. Now press and hold the Input Selector until the Program

Indicator flashes, then release it. Next press the Input Selector

that corresponds to the device type you want to program into

the HDMI 2 mode, i.e., DVD, VCR or CBL/SAT. Then follow the

directions in Step 4.

Figure 2 – Input Selectors

4. Enter a code from Step 1 above.

a) If the device turns off, then press the Input Selector again to accept

the code; the selector will flash. The remote will exit the Program mode.

b) If the device does not turn off, try entering another code. If you

run out of codes, you may search through all of the codes in the

remote’s library for that product type by pressing the

⁄

Button repeatedly until the device turns off. When the device turns

off, enter the code by pressing the Input Selector, which will flash.

The remote then exits Program mode.

NOTE: When you enter a valid three-digit code, the Program

Indicator LED will change in color to green. However, entering an

invalid code changes the color of the LED to red.

5. Once you have accepted a code, it’s a good idea to try using some

other functions to control the device. Sometimes manufacturers

use the same power code for several different models, while other

codes will vary. You may wish to repeat this process until you’ve

programmed a satisfactory code set that operates most of the

functions you frequently use.

6. You may find out which code number you have programmed by

pressing and holding the Input Selector to enter Program mode. Then

press the Set Button, and the LED will flash in the code sequence.

One flash represents “1”, two flashes for “2” and so forth. A series of

many fast flashes represents “0”. Record the codes programmed for

each device in Table 1.

RCP7 OM.qxd 3/23/07 4:15 PM Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon RCP 7 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info