Bedienungsanleitung Harman Kardon RCP 7 (Seite 12 von 24) (Englisch)

456600

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

The following keys on the RCP 7 remote may be programmed with

individual IR codes that are “learned” from another remote control:

Power On/Off, Mute, Sleep/Audio and DSP Surround/Title (Channel

Up/Down), Volume Controls, Channel Level/Disc Menu, Speaker/DVD

Setup, Digital Input/Drawer Open/Close, Delay/DVD Status,

‹›

⁄¤

Navigation, Set/Enter, Numeric Keys, Track Skip Up/Down and Transport

Controls – a total of 34 buttons.

Follow these steps to learn individual key codes:

1. Place the RCP 7 and the device’s original remote so that their IR

transmitters face each other end to end, separated by about one

inch (see Figure 3). The RCP 7 remote’s transmitter also serves as

an IR receiver during the learning process.

Figure 3 – RCP 7 and Original Remote, Head to Head

2. Make sure the RCP 7 is in the device mode you want to learn

the new key code for by pressing the Input Selector, which should

light in red, or green if it is a secondary source on a dual-source

selector. If necessary, press a dual-source selector twice to select

between the primary and secondary sources. Place the RCP 7

remote in Learning mode by pressing and holding the Learn Button

until the Program Indicator flashes amber, then releasing it (see

Figure 4).

Figure 4 – Learning Remote Commands

3. On the RCP 7 remote, press and hold the button you wish to program

with the new code until the Program Indicator remains steadily lit in

amber, then release it.

4. On the device’s original remote, press and hold the button whose

code you wish to “learn” until the RCP 7’s Program Indicator flashes

green, then release it.

5. You may program additional buttons by repeating Steps 3 and 4.

To exit Learning mode, press the Learn Button once. If you prefer,

you may wait for the remote to “time out” and exit Learning mode

on its own, but this will take about 30 seconds.

If you make a mistake while learning a code, you may either learn

a new code over the old code, or else erase the learned code, which

returns the button to the code in the original code set that you

programmed into the Input Selector. To erase a single learned code:

1. Make sure the RCP 7 is in the device mode containing the learned

code you wish to erase by pressing the Input Selector, which should

light in red, or green if the secondary source on a dual-source

selector is active.

2. Press and hold the Learn Button until the Input Selector lights and

the Program Indicator flashes amber, then release it.

3. Press the Input Selector again and release it.

4. Enter the code “777” by pressing the “7” Numeric Key three times.

The Input Selector should flash each time.

5. Press the button whose learned code you wish to erase and release.

The Program Indicator will flash green to confirm the erasure.

6. Repeat Step 5 for any other buttons whose learned codes you wish

to erase.

7. Press the Learn Button to exit Learning mode, or wait about 30

seconds for Learning mode to time out.

To erase all of the learned codes for a device mode:

1. Make sure the RCP 7 is in the device mode containing the learned

code you wish to erase by pressing the Input Selector, which should

light in red, or green if the secondary source on a dual-source

selector is active.

2. Press and hold the Learn Button until the Input Selector lights and

the Program Indicator flashes amber, then release it.

3. Press the Input Selector again and release it.

4. Enter the code “888” by pressing the “8” Numeric Key three times.

The Input Selector should flash each time. The Program Indicator

will flash green to confirm the erasure.

To erase all of the learned codes on the remote for all device modes,

but without erasing other user settings such as product code sets or

punch-through programming, follow these steps:

1. Press and hold the Learn Button until the last-used Input Selector

lights in red and the Program Indicator flashes amber, then release it.

2. Press any Input Selector and release it.

3. Enter the code “999” by pressing the “9” Numeric Key three times.

The Input Selector should flash each time. The Program Indicator will

go dark, and the Input Selector you pressed in Step 2 will remain lit for

about 10 seconds. Then the Program Indicator will flash green to con-

firm the erasure, and the remote will automatically exit Learning mode.

LEARNING INDIVIDUAL KEY CODES

RCP7 OM.qxd 3/23/07 4:15 PM Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon RCP 7 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info