Bedienungsanleitung Hayward K-Flo Pump (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

801924

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

6 Pump

Electrical connection: Make sure that the power supply voltage required by the motor corresponds to that

of the distribution network and that the power supply cables matches the power and current of the pump.

All the electric connections of the pump and the possible change of power supply

cable must be hand-led by a qualied professional so as to avoid all possible danger.

When making these electrical connections, refer to the diagram given under the lid of the motor terminal box.

Be sure to check the electric connections are tight and sealed before powering up.

The pre-wiring that might be included on some of the pumps must be removed for nal connection of the

pump to the electric power supply. This pre-equipment is only used for works testing during the manufacturing

phases.

INSTALLATION

Install the pool pump so as to reduce pressure drops to a minimum whilst complying with the distances

specied in the installation standard, namely 3.5m minimum between the pump and the pool. The suction pipe

must be installed with a slight uphill incline towards the pump axis. Ensure that the connections are correctly

tightened and watertight. However, avoid excessively tightening the pipes. For plastic materials, use Teon

only to ensure watertightness. The diameter of the suction pipe shall depend on that of the discharge pipe.

Avoid damp or non-ventilated locations. The motor requires the cooling air to circulate freely.

IMPORTANT: Check the direction of rotation before permanently connecting the motor.

INSTRUCTIONS FOR START-UP AND PRIMING: Fill the body of the strainer with water up to the level of

the suction pipe. Never run the pump without water, as the water is necessary for cooling and lubrication of

the mechanical shutter. Open all the suction and discharge pipe valves, and the lter air purge valve if there

is one. (Any air in the suction pipes must be eliminated). Start up the generator and wait a reasonable time

for priming. Five minutes is not excessive for priming (this time depends on the suction head and the length

of the suction pipe). If the pump does not start or does not prime, please refer to the troubleshooting guide.

MAINTENANCE

1. Completely disconnect the pump from the mains power supply before opening the cover and cleaning the

strainer. Clean the strainer basket regularly. Do not bang on the basket to clean it. Check the seal on the

cover of the strainer and replace it if necessary.

2. The motor shaft is mounted on self-lubricating bearings which do not require any subsequent lubrication.

3. Keep the motor clean and dry and ensure the ventilation openings are not blocked.

4. The mechanical seal occasionally starts to leak and must then be changed.

5. Apart from cleaning the pool, all repairs, servicing and maintenance must be carried out by a HAYWARD-

approved agent or a qualied person.

Wear parts of the pump mentioned below should be maintained according to their estimated life:

Wear parts Estimated life

Mechanical seal 1 year

Motor bearings kit 1 year

Set of gasket (strainer, housing, bulkheads, drain) 2 years

Capacitor 2 years

WINTERING

1. Empty the pump by removing all the drain plugs and store them in the strainer basket.

2. Disconnect the pump, remove the pipe connectors and store the entire unit in a dry, well-ventilated place

or at least take the following precaution: disconnect the pump, remove the 4 bolts attaching the pump

housing to the motor bracket and store the unit in a dry, well-ventilated place. Then cover the pump

housing and strainer to protect them.

N.B.: Before recommissioning the pump, clean all the internal parts to remove dust, lime scale etc

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward K-Flo Pump Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info