Bedienungsanleitung Hayward RSII DI Pump (Seite 11 von 65) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

801925

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Page 4 of 6 Pump Rev. A

GENERAL POINTS

Install the pump at a suitable distance from the pool to reduce the distance between the suction point and the pump as much

as possible to avoid pointless excessive pressure drops on the hydraulic circuit.

However, it is essential to comply with the safety distance required by the current installation standard (3.5 metres minimum).

Install and use the product at an altitude less than 2000m

ZONE 2 ZONE 2

ZONE 0

1,50 m

2,50 m

1,50 m 2,00 m 2,00 m 1,50 m

ZONE 1

1,50 m

OK OK

3.5 m

ZONE 0

Install the pump in a dry, well-ventilated place. The motor requires the air to circulate freely around it to allow natural

ventilation. Check regularly that no objects, leaves or other debris are blocking the motor cooling system.

The pump must be installed to ensure that the external disconnection switch incorporated into the fixed unit is visible and

easily accessible. The switch must be located near to the pump.

The pump must be permanently installed on a concrete base using 8mm lag screws suitable for concrete, screwed into

drilled implantation holes. Lock washers must be used to prevent the installation lag screws working loose over time. If the

pump has to be mounted on a wooden board, Ø 8mm hexagonal wood screws must be used combined with lock washers

to prevent the screws working loose over time.

The acoustic pressure of Hayward pumps is less than 70dB (A).

Necessary measures:

• Connect the pump to the earth: Never operate the pump unless it is connected to the earth.

• Connect the pump with a H07RN-F 3G1mm² type cable (D max 7,8mm)

• Include a 30mA differential protection to protect people against electric shocks which may be caused by a breach of the

equipment's electrical insulation.

• Include short-circuit protection (the rating is determined according to the value given on the nameplate on the motor).

• Include a means of disconnection from the power supply having an opening distance on the contacts of all the poles ensuring

the power supply is completely cut off under the conditions of a category III overvoltage.

Single phase electric motor:

The single phase motors fitted to our pumps are provided with thermal protection. This protection operates on an overload

or in the event of abnormal heating of the motor coil and is reset automatically when the winding temperature drops.

Three phase electric motor:

On three phased motors the internal heat protection (screw terminal blocks ) is to be connected serially in the pump’s

power contactor command line.

Check the running direction of the pump motor (a label is provided on the motor housing to indicate the motor running

direction).

If so required by regulations and whatever the motor type, in addition to the devices mentioned above, it is also necessary

to install a thereto-magnetic protective device calibrated in accordance with the indications on the motor name-plate.

The table on page 108 indicates the various characteristics of the motors fitted to our pumps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward RSII DI Pump Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info