Bedienungsanleitung Hayward RSII DI Pump (Seite 13 von 65) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

801925

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Page 6 of 6 Pump Rev. A

TROUBLESHOOTING

A) The motor does not start

1. Check the electrical connections, switches or relays, and the circuit breaker or fuses.

2. Ensure that the motor turns freely by hand.

B) The motor stops, check

1. The cables, connections, relays etc.

2. Voltage drop on motor (frequently caused by cables that are too small).

3. That there is no seizing or overheating (by reading the absorbed current).

N.B.: The motor on your pump is fitted with a thermal protection which, in the case of overload, will automatically cut the

circuit and avoid the motor being damaged. This triggering is caused by abnormal usage conditions which need to be

checked and corrected. The motor will restart without any intervention as soon as normal operating conditions are restored.

C) The motor growls but does not start, check that a phase is not cut, the capacitor is not damaged.

D) The pump does not prime

1. Ensure the strainer housing is filled with water, that the cover seal is clean and correctly positioned and that no air can

enter. If necessary, tighten the cover lock screws.

2. Ensure that all the suction and discharge valves are open and not blocked and that the suction outlets in the pool are

fully submerged.

3. Check that the pump draws by freeing the suction as close as possible to the pump:

a) if the pump does not draw despite being sufficiently full of priming water

1. Tighten the bolts and pipe accessories on the suction side.

2. Check the voltage to ensure that the pump is rotating at the correct speed.

3. Open the pump and check that nothing is blocking it inside,

4. Replace the mechanical shutter.

b) If the pump is drawing normally, check the suction pipe and strainer which may be blocked or be allowing air to enter.

E) Low flow - Generally, Check for :

1. Clogged or restricted strainer or suction line; undersized pool piping.

2. Plugged or restricted discharge line of filter (high discharge gauge reading).

3. Air leak in suction (bubbles issuing from return fittings).

4. Pump operating under speed (low voltage).

5. Plugged or restricted impeller.

F) Noisy pump, check

1. That no air is entering the suction side and causing dull crackling in the pump.

2. That there is no cavitation caused by insufficient diameter or a restriction in the suction tube. An over-sized discharge

pipe can also cause cavitation. Use pipes of the correct size or purge the pipes if necessary.

3. That no vibration is occurring due to incorrect fitting.

4. That there are no foreign bodies in the pump housing.

5. That the motor bearings have not seized due to excessive clearance, rust or prolonged overheating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward RSII DI Pump Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info