741833
7
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
7
EN
5. MAINTENANCE AND CLEANING
Warning: before performing any task disconnect the appliance from the electric power supply.
GENERAL CLEANING
Carry out cleaning when the oven is cold. Do not use
products containing chlorine to clean steel (sodium
hypochlorite, hydrochloric acid, etc) even if they are
diluted. Use specifi c commercial products and a lit-
tle hot vinegar.
Rinse well with water, without using direct jets, and
dry with a soft cloth.
Clean the glass door of the oven with hot water and
do not use coarse cloths.
CLEANING THE OVEN
The inside of the oven should be cleaned at the end
of each day’s work. In this way it will be easier to
remove cooking residue so as to prevent it burning
the next time the oven is used.
When the oven is cold, clean it thoroughly with the
appropriate commercially available products.
REPLACING THE OVEN LAMP
Disconnect the appliance electrically; remove the later-
al
support for cooking vessels by lifting the support
upwards. Wait for the cover and the lamp to cool
and then unscrew the protecting glass cover without
using tools so as to avoid breakages. Unscrew the
lamp and replace it with another one having these
features:
Voltage: 230/240 V, power: 15 W, attachment: E14
Refi t the glass cover and the lateral cooking vessel
support and connect the power supply.
MAINTENANCE
Our appliance does not require scheduled mainte-
nance but an annual maintenance contract should
nevertheless be drawn up in order to keep the appli-
ance safe and in perfect working order.
For information purposes, maintenance must apply to:
gas part – pressure adjustment, checking seal,
correct operation, status of switch-on electrode,
fume discharge, etc.
electrical part – checking power cable, lamps and
pilot lights, checking electrical resistances, fan
and safety systems, etc.
hydraulic part – checking seal of water system,
jet of humidifi er, water pressure, etc
internal cleaning – removal of residue from cook-
ing chamber, including fan blades (after removal
of fan cover), removal of residues from discharge
routes, etc.
ELECTRICAL DATA TABLE
Terminal block fi tting for 3 x 1.5 mm cable, voltage 230 VAC 50 HZ class 1
Fitting for circuit breaker connection for cables up to 3 mm2
WATER DATA TABLE
Water inlet fi tting = ¾ inch thread with seal washer
Drainage fi tting = stainless steel pipe, 25 mm diameter.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hendi 225929 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info