Bedienungsanleitung Hendi 239438 (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741240

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Preparations before using for the first time

• Remove all protective packaging and wrapping.

• Check to make sure the appliance is undamaged.

In case of incomplete delivery and damages.

Please contact supplier (See ==> Warranty).

• Clean the appliance before use (See ==> Cleaning

and Maintenance).

• Make sure the appliance is completely dry.

• Place the appliance on a horizontal, stable and

heat resist surface that is safe against water

splashes.

• Ensure that there is sufﬁcient ventilation. Keep

a minimum distance of 15 cm around the appli-

ance.

• Do not place the appliance in close proximity to

devices which are sensitive to disturbances by

magnetic sources (e.g. radios, tape decks).

Note: Due to manufacturing residues, the appli-

ance may emit a slight odor in the ﬁrst few cycles.

This is normal and does not indicate any defect or

hazard. Make sure the appliance is well ventilated.

Suitable cooking equipment

Suitable Not suitable

Bottom of cookware Flat bottom

Curved, uneven, rounded bottom

Material Cookware with iron, cast iron, mag-

netic stainless steel or enamelled iron

bottom.

Cookware with ceramic, glass, copper,

bronze, or aluminium bottom.

Diameter of the bottom Between 12 cm and 22 cm. Less than 12 cm or more than 22 cm.

Type of cookware Cookware with a bottom thickness

over 1.5 mm.

Completely closed containers or cans.

Note: Using a pan or pot that’s not suitable for induction cooking may damage the appliance.

Operation

• Place a suitable pan or pot at the centre of the

heating surface of the appliance. (See --> Suitable

pans for the appliance).

Note: Do not place empty pan as this may damage

the pan and the appliance.

• Connect the power plug to a suitable electrical

supply outlet. On/Standby button (1) will be light

up and the appliance now in Standby mode.

• Upper control for rear panel, lower control for

front panel.

• Switch On the appliance by pressing the On/

Standby button (1) ﬁrst, then pressing Increase

setting (2) to start.

• Now the power function is on. The appliance is

ready for cooking. If the timer is not activated, the

appliance will operate continuously.

• Choose panel and adjust the setting by following

description.

• Switch off one of the heating panel separately by

pressing Decrease setting (4) continuously.

• Once you have ﬁnished cooking, switch to standby

mode by pressing the On/Standby button (1). The

digital display (3) and all buttons will go off except

On/Standby button (1).

Note:

1) After an extended period of operation, it is nor-

mal for the cooling fan inside to continue run-

ning in OFF mode for some time. Before unplug

the appliance, wait until the cooling fan stops

running.

2) If no cookware is placed on the heating surface

during operation, it will turn to OFF mode auto-

matically within 1 min.

3) If no any button on the control panel is pressed

during operation for 2 hours, the appliance will

then switch to OFF mode automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 239438 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info