741179
10
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
10
EN
Troubleshooting
If the machine does not function properly, please check the below table for the solution. If you are still un-
able to solve the problem, please contact the supplier/service provider.
Problems Possible cause Possible solution
The machine does not switch on.
Power plug is not connected properly with
the electrical power outlet.
Make sure the power plug is connected
properly with the electrical power outlet.
The vacuum bag is not vacuum and / or
sealed completely.
Vacuum/ Seal time is not long enough. Set longer Vacuum/Seal time.
The opening of the vacuum bag was not
entirely and properly placed under the
sealing bar (8).
Pack the food in a new bag and place
properly in the chamber so the entire
opening can be sealed. Don’t use bags
that don’t fit the sealing bar.
The sealing bar (8) and the inside vacuum
chamber (9) is not clean enough.
Wipe the surface of the sealing bar (8)
and inside the vacuum chamber (10) to
keep clean, dry and free of debris.
There is some moisture, food particles or
debris on the seal area of the vacuum bag.
Wipe the seal area of the vacuum bag to
make sure it is dry and clean.
Vacuum bag loses vacuum after being
sealed.
Inside the vacuum bag has food with
sharp points to penetrate the bag and
thus air enters into the vacuum bag.
Cut off the sharp points or cover it before
packing.
Some food can release gases also food
can release gases due to food spoilage.
Blanch or frozen the food properly before
packaging. Discard the food if in doubt.
Error codes display
Error codes shown on the digital display
(F)
Possible cause Possible solution
E01 - The lid (1) is not properly closed.
- Oil pump is defective.
- Machine internal system is defective.
- The lid (1) is not properly closed.
- Contact the supplier.
- Contact the supplier.
LP - Machine lost electrical power supply
suddenly during operation.
- Check the electrical power supply.
Technical specification
Item no. 201442
Operating voltage and frequency 220-240V~ 50 / 60 Hz
Rated input power 1100W
Protection class Class I
Max vacuum bag width 410 mm
Pump capacity 333,3 L/min
Pressure -29,9” Hg / -1012 mbar (± 3%) directly at the pump
-29,8” Hg / -1009 mbar (± 3%) in vacuum chamber
Width of sealing bar 2 x 3,5 mm
Dimension 505 x 567 x (H) 465 mm
Net weight approx. 60kg
Remark: Technical specification is subjected to change without prior notification.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hendi 201442 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info