742508
5
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
5
EN
Preparation for installation
After unpacking of the device, a power supply, a
2.5” wrench for the head flange, 3/4” seals and 3/4”
connectors shall be taken out of the brine tank.
Only the special recesses in the housing shall be
used to lift and move the device around. The device
shall not be lifted by its electric cables or water
hoses due to damage that might occur.
Before installing, ensure that water mains pres-
sure is above 1.5 bar and below 6.0 bar. Shall the
pressure be higher, a reducing valve shall be in-
stalled upstream the device.
A location as close as possible to the water inlet of
a building shall be chosen (a water meter in case
of mains water supply or a hydrophore in case of
own water source/inlet) and in the vicinity of drain-
age. Moreover, permanent electric power supply is
necessary, therefore a socket must be near. The
surface of installation must be stable and must
withstand the weight of the device filled with water.
Ambient temperature in the selected installation
area shall never drop below 5°C, otherwise the
device may be permanently damaged. The devices
shall not be installed in rooms with excessive air
humidity. What is more, the selected area shall be
large enough to guarantee free access to the de-
vice, as it requires periodical refilling of salt.
Installation
The connectors of the control head are marked as
IN (inlet) and OUT (outlet), looking from the front of
the control head: IN (inlet) on the right, OUT (out-
let) on the left. The seals and connectors provided
shall be placed/fixed onto the connectors of the
control head. The water softener shall be connect-
ed to the system with flexible hoses (not provided).
A mechanical filter shall be installed upstream the
softener, of at least 50 microns, in order to protect
the device against impurities.
A by-pass can be executed by means of regular
valves, as indicated in Fig. A. A turbine must be in-
stalled in a nipple fixed onto the “OUT” connector
of the control head. Before installation, make sure
that the turbine rotates freely (e.g., by blowing air
into the water outlet). The device shall be installed
by means of materials intended for water installa-
tions. In case of any problems or doubts, contact
a qualified installation company or an authorized
service company.
Diagram of the device
Control head
Cover
Flange
Upper basket
Overflow elbow
Distrubution pipe
Resin
Lower basket
Brine valve pit
Brine valve
Cabinet
Salt
Container
Fig. A
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hendi 230442 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info