Bedienungsanleitung Hendi 230442 (Seite 7 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

742508

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Before first switch-on

For safety reasons, it is recommended that the wa-

ter installation of the device is vented before the

ﬁrst switch-on. In order to do so, water inlet to the

softener must be shut off. Consecutively, the sam-

pler valve after the water softener must be opened,

whereas the mains valve of the building shall be

opened gently. Water ﬂowing will push air out

through the open sampler valve. A bubbling sound

will appear and water may gush. One shall wait un-

til the ﬂow of water stabilizes and then close the

sampler valve. The system is now vented.

Venting. Filling water into the device

In order to vent the device, the sampler valve after

the water softener must be opened, whereas the

mains valve of the building shall be opened gently.

Then, one shall proceed as in the case of venting

the entire system. It is recommended that the de-

vice is ﬁlled with water gradually, with breaks, in

order not to increase pressure inside the device

abruptly.

ATTENTION! The salt tank must be ﬁlled with salt and water before the ﬁrst switch-on of

the device. One shall wait 30 minutes before salt dissolves in water. Resin regeneration

must then be performed.

First resin regeneration (ONLY 230459 model)

Regeneration must be activated with the usage of the manual regeneration button. Regeneration will

be done automatically. After it ﬁnishes, the device is ready to operate.

Operating cycles of the device

In serve the device is in the position of the ﬁrst operation cycle, i.e. water treatment. Water

ﬂows though the device. Raw water enters the container with resin through the

controller, ﬂows through the resin and is directed upwards, through a distribution

pipe, to the controller and further to the system.

BACKWASH

The device is in the position of the second operation cycle - anti-current rinse

(backwash). Raw water enters the container with the ﬁlter bed through an inlet valve and

is directed downwards with a central pipe. Water ﬂows through the resin, rinses it and

ﬂuffs it, and then is directed to sewage. In this cycle the controller shuts off water inlet

to the water system. Thanks to which the controller protects the water system against

the penetration of impurities from rinsing.

BRINE DRAW SLOW RINSE T

he device in the position of third operation cycle - regeneration with brine and slow

rinsing. Raw water with brine enters to the container with the ﬁlter bed through an inlet

valve. Flowing through the bed in the tank, it regenerates its ion exchange capacity. After

ﬂowing through the bed, water is directed to sewage. After all brine in the brine tank is

used up, the ion exchange bed is rinsed slowly with water, which guarantees thorough

rinsing brine and proper regeneration conditions. In this cycle the controller shuts off

water inlet to the water system. Thanks to which the controller protects the water

system against the penetration of impurities from rinsing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 230442 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info