Bedienungsanleitung Henkelman MARLIN (Seite 16 von 43) (Englisch)

647373

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 16

4. Gas flush function Once the vacuum function has completed then the gas flush function starts to flush gas into

(if installed) the vacuum chamber.

The light in front of [GAS] goes on.

Large Display: decrementing time per second starting at the time set (max. 99 sec.).

Vacuum meter starts decreasing to the right.

5. Seal function When the vacuum function or gas flush function (if installed) ends, the seal function starts to

seal the vacuum bag(s).

The light in front of [SEAL] goes on.

Large Display: decrementing time per 0.1 second starting at the time set (max. 6.0 sec.).

The reading on the vacuum meter stays the same.

6. Soft-air ventilation function After ending the seal function the soft air function starts to slowly ventilate the vacuum

(if installed) chamber.

The light in front of [SOFT AIR] goes on.

Large Display: decrementing time per second starting at the time set (max. 99 sec.).

Vacuum meter starts slowly decreasing to the right.

7. Ventilation function After ending the seal function or the soft air function (if installed) the ventilation function starts

ventilating the chamber to 1 atmosphere/ATO and the lid opens.

There are no longer any lights on in front of the functions.

Large Display: lines going up and down until the lid is opened.

The vacuum meter runs back to the right to zero and the lid opens automatically.

8. The product is packed and ready to remove.

Description of the program cycle for digital sensor control

1. Select the program number with the PROG key and the small display.

If the selected program is programmed with the active gas flush function then a dot appears in the lower right hand corner of the

small display.

If the selected program is programmed with the active VACUUM PLUS function then a dot appears in the lower right hand corner

of the large display.

2. Close the lid.

3. Vacuum function The machine starts to vacuum the chamber.

The light in front of [VACUUM] goes on.

Large Display: incrementing percentage vacuum until the percentage set (max.. 99%) and a

dot in the lower right hand corner if the VACUUM PLUS function is activated.

Vacuum meter starts increasing to the left.

4. VACUUM PLUS function The machine continues vacuuming the chamber after 99% value is reached.

(if installed) The light in front of [VACUUM] goes on.

Large Display: decrementing time per second starting at the time set (max. 99 sec.). and a

dot in the lower right hand corner.

The vacuum meter will very slowly increment to the left (hardly noticeable).

Remark: can only be installed with a vacuum function whereby the value is set to the

maximum of 99%.

5. Gas flush Function Once the vacuum function has completed then the gas flush function starts to flush gas into

(if installed) the vacuum chamber.

The light in front of [GAS] goes on.

Large Display: decrementing percentage vacuum until the set percentage (min. 30%).

Vacuum meter starts decreasing to the right.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman MARLIN Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman MARLIN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info