Bedienungsanleitung Henkelman MARLIN (Seite 17 von 43) (Englisch)

647373

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 17

6. Seal function When the vacuum function or gas flush function (if installed) ends, the seal function starts to

seal the vacuum bag(s).

The light in front of [SEAL] goes on.

Large Display: decrementing time per second starting at the time set (max. 6.0 sec.).

The reading on the vacuum meter stays the same.

7. Soft-air ventilation function After ending the seal function the soft air function starts to slowly ventilate the

(if installed) vacuum chamber.

The light in front of [SOFT AIR] goes on.

Large Display: decrementing time per second starting at the time set (max. 99 sec.).

Vacuum meter starts slowly decreasing to the right.

8. Ventilation function After ending the seal function or the soft air function (if installed) the ventilation function starts

ventilating the chamber to 1 atmosphere/ATO and the lid opens.

There are no longer any lights on in front of the functions.

Large Display: lines going up and down until the lid is opened.

The vacuum meter runs back to the right to zero and the lid opens automatically.

9. The product is packed and ready to remove.

PROGRAM MODE

The program mode is used to change the function values within the programs. See page 18-20 for instructions on

programming.

OTHER MODES

The control panel also includes a service mode. The conditioning program (see page 22) for the pump and the operation

hours counter are the functions most used in this mode.

Operation Hours Counter

One of the service functions is the operation hours counter in order to be able to automatically indicate regular service

requirements. This functions sets the number of hours that the pump runs (per 10 hours). Note that for BOXER series

and MARLIN 42-42 XL, the pump does not run continuously. Once the number of hours set has been exceeded, the

message [OIL] appears on the display (see page 11). The machine can still be used as usual but the message will keep

reappearing on the display.

The factory setting for the program operation hours counter is OFF (turned off). The following steps can be followed to

activate the operation hours counter or to reset it:

Press the FUNCTION SELECT Key for at least 3 seconds. After 3 seconds the number of operating hours

(per 10 hours) will be displayed for about 2 seconds. After 2 seconds the originally set number of hours will

be displayed (per 10 hours). When the operation hours counter is turned off, the number of operating

hours will not be displayed, instead the message [OFF] will immediately appear after pressing the key for 3

seconds.

The original setting can be modified using the + and – keys (between 0 and 990 hours). If set to 0 then the next time

[OFF] will automatically be displayed. The new settings are stored by using the REPROG Key. The actual operation

hours are then also reset to zero.

After pressing the REPROG key, the control panel automatically switches over to operation mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman MARLIN Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman MARLIN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info