Bedienungsanleitung Henkelman POLAR (Seite 22 von 43) (Englisch)

647375

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

BOXER / MARLIN / FALCON / POLAR SERIES USER MANUAL

Version 06.03 DIG.EN 22

STANDARD MAINTENANCE SCHEDULE FOR THE MACHINE

Daily

 Clean the vacuum chamber, lid, and housing after use with a damp cloth.

 Make sure that no cleaning agents containing solvents are used.

 Make sure that no high pressure cleaner is used.

Weekly

 Check the oil level and replace or fill up oil when the oil is turbid or the oil level is too

low. For instructions, see page 23.

 Activate the conditioning program for the pump at least once a week.

 Inspect the sealing bar for damage. Replace teflon tape/sealing wire if the seal quality

is no longer sufficient or if the teflon tape/sealing wire is no longer tight and straight on

the sealing bar. For instructions, see page 26.



Inspect the lid gasket and replace it when the gasket is damaged or stretched. For

instructions, see page 27.



Inspect the transparent lid (if applicable). When cracks are visible, turn off the machine

immediately and contact the supplier or Henkelman BV.

Every Six Months

 Replace oil at least once every 6 months.

Yearly

 Inspect the oil exhaust filter for saturation. If saturated, replace the filter. For

instructions, see page 24.

 Contact the supplier for a professional service

Four-yearly

 Replace transparent lid and the lid’s gas springs (if applicable)

 Replace membranes sealcylinder (if applicable)

VACUUM PUMP MAINTENANCE

It is very important to regularly service the pump to ensure extended and correct operation. The following activities are

essential for correct maintenance. If the machine is used regularly then it is advisable to have the pump fully inspected at

least once a year by the supplier to ensure extended and problem free operation. Contact the supplier or Henkelman BV

for more advice and information.

Conditioning Program

The conditioning program ensures that the pump is thoroughly rinsed. During the program the pump and oil

reaches operation temperature so that the oil can better absorb any moisture and contaminants and filter them. The high

temperature enables any moisture in the pump to evaporate minimising the risk for rust spots.

The program lasts 15 minutes and it is advisable to run it at least once a week. Turn on the machine, press the key

[conditioning program], and close the lid. The program runs automatically. During the program the large display will

display moving lines.

The program can be interrupted at any time using the [STOP] key. It is however important for the sake of good

maintenance that the program completes a full 15 minute cycle and therefore advisable only to interrupt the cycle for

something urgent.

It is also advisable to run the program before using the machine for the first time, after the machine has been stationary

for a lengthy period of time, and especially prior to changing oil.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Henkelman POLAR Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Henkelman POLAR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info