Bedienungsanleitung Hifonics BRX2000D (Seite 19 von 32) (Deutsch, Englisch)

700127

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ELECTRICAL INTERCONNECTION

INSTALLATION INSTRUCTIONS

PROTECT BRIDGE

If you would like to operate two similar ampliers in the MASTER/SLAVE mode, connect both ampliers with the appropriate

enclosed cable on the PROTECT BRIDGE port of each amplier. This connection ensures in case of a malfunction or a defect

on one of the ampliers (Master or Slave), that both ampliers will run into the protection mode and shut down.

BEFORE CONNECTING

For the professional installation of a sound system, car audio retail stores offers appropriate wire kits. Ensure a sufcient prole section

(at least 25 mm

), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-

streaked and oxidized areas on the contact points of the battery and the ground connection. Make sure that all screws are xed tight after

the installation, because loose connections cause malfunctions, insufcient power supply or interferences.

FUSE

The inserted fuses protect the amplier from shorts and capacity overload. The standard fuse is only suitable for a 4 ohm spea-

ker load. For a 2 ohm speaker load the current consumption increases by 50% and the fuse(s) may need to be replaced by fuses

with a higher rating.

LOGO

This push button switches the logo illumination on the upper side from blue to white.

GND

Connect the GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be as short

as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground point has a stable

and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the battery to the ground point if

possible and enforce it if required. Use a ground wire with a sufcient cross section (at least 25 mm

) and the same size like the

plus (+12V) power supply wire.

REM

Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote signal of your head unit with the REM-terminal of the

amplier. Use therefor a suitable cable with a sufcient cross section (0,5 mm

). Hereby the amplier turns on or off with your

headunit.

BATT+12V

Connect the BATT+12V-terminal with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufcient cross section

(at least 25 mm

) and install an additional in-line fuse. For safety reasons the distance between the fuseblock and the battery

should be shorter than 30 cm. Do not set in the fuse into the fuseblock until the installation is accomplished.

1 32 4 5 6

BLUE / WHITE

LOG0

50A

POWER INPUT

SPEAKER OUTPUT

PROTECT

POWER

SLAVEMASTER

LEVEL

BASS LEVEL

CONTROLLER

AUTO TURN ON

(ONLY IN HI LEVEL INPUT MODE)

0dB 18dB

LINE IN SLAVE IN/OUT

LEVEL

INPUT

MODE

35Hz 250Hz

MIN MAX

OFF

LOW

SUB

BOOST

Q-CONTROLPHASE

FREQ.

RANGE

SUB SONIC

15Hz 55Hz

GND +12VREM

FUSE

BRX1500 D

EXTENDED BASS CONTROL

WIDE NRW20Hz 80Hz

0° 180°

BALANCED

INPUT

BRX1500 D

PROTECT

BRIDGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics BRX2000D Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info