168839
15
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Speaker & RCA Connections
TXi 1700
FULL-MODE / Connection of a Loudspeakersystem
• Connect the "LINE IN" of the amplifier to the head unit´s line output with appropriate good quality RCA cables.
• Connect the speakers with appropriate wires to the terminal block (SPEAKER OUTPUT - and +) of the amplifier.
• The minimum final speaker impedance must not be lower than 1 Ohms in total. Too low speaker loads result in too high heat dissipation and may
cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
• Caution: The loudspeakers don´t get a stereo-signal. If you want to get a stereo-signal you have to use a second amplifier in
Master/Slave-Mode.
• If your head unit has an subwoofer line output with an integrated crossover you are able to use one or two subwoofers in Full-Mode.
In this mode PHASE - Control, LOW PASS - Control, SUB SONIC - Control and BASS REMOTE are out of function.
MODE - Switch
• Set the switch in this operation mode to "FULL" - position.
FREQ RANGE - Control
• Allows you to adjust the frequency at which the bass boost should work. It is continously variable between 20Hz up to 80Hz.
Q-Control
• Allows you to adjust the filter performance Q of the crossover. So you can change the playback quality in the range of the cut-off
frequency."WIDE" Q - 0.3, "NARROW" Q - 1.0. Regular setting is on 12 o`clock - position Q - 0.5/Linkwitz-Reilly and
3 o`clock - position Q - 0.7 /Butterworth.
SUB BOOST - Control
Allows you to adjust the bass boost from 0dB up to 18dB.
LEVEL
• Turn the LEVEL control of the amplifier to 6V position.
• Turn the head unit volume control to about 80 - 90% of its full setting.
• Turn the LEVEL control clockwise until you hear some distortion.
• Then turn back the LEVEL control slightly until you can hear a clean sound.
In this example the Bass-Remote-Control can not be used!
By using a additional subwoofer,
connect it to the non-occupied
terminals, ensure that the total
impedance load is not lower
than 1 Ohm.
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
+
+
Mono Speakers 2 - 8 Ohm
Connect RCA outputs of the head unit with
LINE IN of the amplifier.
15
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics txi 1700 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info