Bedienungsanleitung Hifonics zxi8805 (Seite 20 von 28) (Deutsch, Englisch)

168668

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

SPEAKER OUTPUT

+ –

CH 1 CH 2

+ MONO BRIDGED –

+ – + –

CH 3 CH 4

+ MONO BRIDGED –

+ –

021586

FUSE

LOGO

BADGE

BLUE

WHITE

POWER INPUT

+ –

CH 5

GND BATT +12VREM

5-CHANNEL AMPLIFIER: ZXi8805

Interconnetion example: 3-Way-Active-System and Subwoofer

Connect the stereo RCA output of the headunit

with LINE INPUTS CH1/2 of the amplifier.

Low-/Mid-

Speaker

2 – 8 Ohms

Low-/Mid-

Speaker

2 – 8 Ohms

CH 3

CH 4

LINE INPUT

CH 1

CH 2

CH 5

LEVEL HI PASS

6V 0. 2V

50Hz

150Hz

BASS BOOST LEVEL

0dB 10dB 6V 0.2V

50Hz 4kHz

LOW PASS

30Hz 150Hz

X-OVER

CH 1/2

FULL

REMOTE

HI PASS LOW PASS

HP FULL BP

X-OVER

CH 3/4

LEVEL

6V 0.2V250Hz 4kHz

CH 5

POWER

PROTECT

MODE

4 CH 5 CH2 CH

R L

Tweeter

2 – 8 Ohms

Tweeter

2 – 8 Ohms

Subwoofer

2 – 8 Ohms

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT CH1/2 of the amplifier with appropriate high-value RCA

cables.

• Connect the tweeters with SPEAKER OUTPUT + CH1 - / + CH2 -.

• Connect the low-/mid-speakers with SPEAKER OUTPUT + CH3 - / + CH4 -.

• Connect the subwoofer with SPEAKER OUTPUT + CH5 -.

• Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature

and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

MODE SWITCH

• Select the 2CH position on the MODE switch.

CROSSOVER SETTINGS CH1/2 (Tweeter)

• You must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage by lower frequencies on the speakers.

The cut-off frequency is adjustable with the HI PASS controller and should be set between 2500Hz to 4000Hz, depending on the size

of the speakers.

CROSSOVER SETTINGS CH3/4 (Low-/Mid-Speaker)

• You must set the X-OVER switch to the BP Position (Bandpass Mode) to avoid any damage by lower frequencies on the speakers.

The lower cut-off frequency is adjustable with the HI PASS controller and should be set between 60Hz to 150Hz. The higher cut-off

frequency is adjustable with the LOW PASS controller and should be set between 1800Hz to 3800Hz, depending on the size of the

speakers.

LEVEL CONTROLLER CH1/2 & CH3/4 & CH5

• Turn the LEVEL controller of the amplifier to the 6V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

BASS BOOST CONTROLLER CH5

• The BASS BOOST controller is continuously adjustable from 0dB bis +10dB.

LOW PASS CONTROLLER CH5

• The LOW PASS controller is for the adjustment of the Cut-Off-Frequency, which should be between 60Hz and 100Hz, depending on

the size of the subwoofer.

BASS REMOTE CH5

• The enclosed BASS REMOTE Controller adjusts the bass-level on CH5 e.g. from the driver’s seat.

Please use only the enclosed bass remote controller and cable.

Connect the bass

remote controller and

the remote terminal on

the amplifier with the

enclosed cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hifonics zxi8805 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info