Bedienungsanleitung Hikoki C1805DA (Seite 15 von 272) (Alle Sprachen)

816213

Zoom out

Zoom in

Vorherige Seite

1/272

Nächste Seite

English

In this case, release the tool switch and cool it down in a

few minutes.

After that you can use it again.

○ Rotation speed changeover function (Power mode /

Silent mode)

(Power mode / Silent mode switch function)

Each press of the Mode Selector Switch changes the

operating mode. (Fig.15)

Silent mode reduces maximum motor RPM enabling

efficient work with less noise.

The Silent Mode Indicator Lamp lights in Silent mode.

When the load increases during Silent mode, the tool

will automatically switch to Power mode and revert back

to Silent mode when the load decreases.

In Power mode, no change is made to Silent mode even

when the load decreases.

NOTE

○ To enable mode changes, pull the switch once after

installing the battery.

○ Do not give a strong shock to the switch panel or break

it. It may lead to a trouble.

2. Battery

Model BSL1850MA

Voltage 18 V

Battery capacity 5.0 Ah

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the pilot lamp will blink in red. (See Table1)

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig.22 (on page 6).

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously in

red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (See Table1)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table1, according to the condition of the charger or the

rechargeable battery.

Table 1: Indications of the pilot lamp

ON/OFF at 0.5sec. intervals Before charging *1

Charging complete

Lights continuously While charging

Lights for 1sec. at intervals of

0.5sec. Overheat standby *2

ON/OFF at 0.1sec. intervals Charging impossible

NOTE

*1 If the red lamp continues to blink even after the charger

has been attached, check to confirm that the battery

has been fully inserted.

*2 Battery overheated. Unable to charge.

Although charging will start once the battery has cooled

down even when left in situ, the best practice is to

remove the battery and allow it to cool down in a

shaded, well-ventilated location before charging.

*3 Malfunction in the battery or the charger

– Fully insert the battery.

– Check to confirm that no foreign matter is stuck to

the battery mount or terminals. If there are no

foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

○ If the pilot lamp does not blink in red even though the

charger cord is connected to the power, it indicates that

the protection circuit of the charger may be activated.

Remove the cord or plug from the power and then

connect it again after 5minutes or so. If this does not

cause the pilot lamp to blink in red, please take the

charger to the HiKOKI Authorized Service Center.

○ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting the

cause of the failures. Once the charging has been

completed, give 15minutes rest until the next charging.

(2) Regarding the temperatures and charging time of the

battery. (See Table2)

Table 2

Model UC18YFSL

Type of battery Li-ion

Charging voltage 14.4–18 V

Temperatures at which the

battery can be recharged 0°C–50°C

Charging time for

battery capacity,

approx. (At 20°C)

1.5Ah 22min

2.0Ah 30min

2.5Ah 35min

3.0Ah 45min

4.0Ah 60min

5.0Ah 75min

6.0Ah 90min

Charging time for

multi volt battery

capacity, approx.

(At 20°C)

1.5Ah

(×2unit) 45min

2.5Ah

(×2unit) 75min

4.0Ah

(×2unit) 120min

Number of battery cells 4–10

Weight 0.5kg

NOTE

○ The recharging time may vary according to the ambient

temperature and power source voltage.

○ If charging takes a long time

2023/08/01 12:32:25Stylesheet: EU Version: 2023.7.24

C1805DA_C99750471_308_EU

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki C1805DA Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info