Bedienungsanleitung Hikoki CG18DA (Seite 19 von 380) (Alle Sprachen)

816209

Zoom out

Zoom in

Vorherige Seite

1/380

Nächste Seite

English

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period is

not activated, the electric discharge might be low when

using them the first and second time. This is a temporary

phenomenon, and normal time required for recharging will

be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool

becomes weaker, stop using the tool and recharge its

battery. If you continue to use the tool and exhaust the

electric current, the battery may be damaged and its life

will become shorter.

(2) Avoid recharging at high temperatures. A rechargeable

battery will be hot immediately after use. If such a

battery is recharged immediately after use, its internal

chemical substance will deteriorate, and the battery life

will be shortened. Leave the battery and recharge it

after it has cooled for a while.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 5 3

Charging 6 4

Remaining battery indicator 23 7

Charging a USB device from a

electrical outlet 24-a 7

Charging a USB device and battery

from a electrical outlet 24-b 7

How to recharge USB device 25 7

Selecting accessories — 372

ASSEMBLY PROCEDURES

WARNING

Pull out battery before doing any assembly.

1. Installing of handle (Loop handle type) (Fig.7)

Attach the handle to the main pipe with the angle

towards the grip side.

Adjust the location to the most comfortable position

before operation.

Make sure to securely attach the handle with the

2bolts.

NOTE

Install the loop handle between the arrow marks on the

handle location label.

2. Installing of guard

WARNING

If an incorrect or faulty guard is fitted, this may cause

serious personal injury.

CAUTION

The guard extension is equipped with the knife. Be

careful with handling it.

Align the guard with the cover bracket and secure it to the

main pipe, using the bolt and cover bracket. (Fig.8)

NOTE

○ The guard extension is already attached to the guard at

the time of purchase.

○ The cover bracket may come already mounted to the

gear case.

3. Installing the shoulder belt

WARNING

○ Be sure to attach the shoulder belt so that the brush

cutter can be carried correctly.

○ If you get the feeling the tool is not operating normally,

turn off the motor immediately, remove the quick-

release bracket of the shoulder belt and remove the

tool.

CAUTION

○ If you do not support the tool when you pull the quick-

release belt, it may fall causing injury or damage. Hold

the main pipe with one hand while you pull with the

other hand.

○ Make sure the quick-release function operates normally

before you start working.

○ Before attaching, check to confirm that the belt is not

cut, frayed, or damaged.

○ Check to confirm that the hook and hanger are neither

deformed nor damaged.

○ Once attached, press down on the main unit to confirm

that the hook does not detach easily and that the

shoulder belt is not loose.

○ Check to confirm that the quick release function

operates as it should.

(1) Place the shoulder belt on the shoulder as shown in

Fig.9 and engage it with the hanger on the tool. Adjust

the shoulder belt to suitable length.

NOTE

You may need to adjust the position of the hanger to

balance the unit. To do so, loosen bolt and adjust the

position of hanger. After adjusting as necessary, make

sure to securely tighten the bolt. (Fig.10)

(2) To remove the tool from the shoulder belt, support the

tool by holding the main pipe with one hand and use the

other hand to pull the quick-release belt as shown in

Fig.11 to free it from the bracket.

(3) To strap on the tool, insert the bracket in the hook and

insert the quick-release bracket over the hook and into

the wide opening of the bracket. (Fig.12)

Gently pull the shoulder belt to make sure that it is

properly attached.

4. Installation of cutting attachment

WARNING

○ Install the cutting attachment properly and securely as

instructed in the handling instructions.

If not attached properly or securely, it may come off and

cause serious and/or fatal injury.

○ Always use genuine HiKOKI cutting attachments and

metal fittings.

[Installation of semi-auto nylon head]

WARNING

For HiKOKI heads, use only flexible, non-metallic line

recommended by the manufacturer. Never use wire or

wire ropes. They can break off and become a

dangerous projectile.

(1) Function

Automatically feeds more nylon cutting line when it is

tapped at low rpm (not greater than 4000 min-1).

2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18

CG18DA(L)_C99750571_311_EU

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki CG18DA Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info