Bedienungsanleitung Hikoki CG18DA (Seite 21 von 380) (Alle Sprachen)

816209

Zoom out

Zoom in

Vorherige Seite

1/380

Nächste Seite

English

○ Release the lever when you finish cutting and stop the

motor.

○ Take a posture that makes it easy to move.

[Using the semi-auto nylon head]

– Do not swing the pipe, but use the hips to move the

nylon head horizontally from left to right in an arc while

going forward and use the right side of the nylon head

for cutting grass. (Fig.20)

[Using the blade]

– Cut grass from right to left, using the left side of the

blade to cut. (Fig.21)

– Slightly tilting the blade to the left while cutting will pile

the cut grass to the left, making collection easy.

WARNING

○ Blade thrust may occur when the spinning blade

contacts a solid object in the critical area.

A dangerous reaction may occur causing the entire unit

and operator to be thrust violently. This reaction is

called blade thrust. As a result, the operator may lose

control of the unit which may cause serious or fatal

injury. Blade thrust is more likely to occur in areas

where it is difficult to see the material to be cut.

○ If cutting attachment should strike against stones or

other debris, stop the engine and make sure that the

attachment and related parts are undamaged.

NOTE

Excessively increasing rotation speed may cause

increased blade wear, vibration and noise. It will also

wear out the battery faster.

6. Carrying the tool

CAUTION

○ Remove the storage battery. (Fig.5)

○ Carry the tool holding with hands.

○ If the blade is installed, attach the included blade cover.

OPERATIONAL CAUTIONS

This tool incorporates a function to safeguard the electronic

components that control the main unit. If an overload

occurs during mowing—for example, if the cutting

attachment locks up or becomes clogged with vegetation—

the function will activate to stop the motor. If this happens,

the power switch (47 in Fig.22) will flash.

Check the signal status and take appropriate corrective

action. (Table3)

You can resume use after taking the following corrective

action. Take steps to reduce the load imposed on the motor

—for example, by reducing the cutting depth. Before

clearing vegetation from the cutting attachment, turn off the

power and remove the battery from the tool main unit.

Table3

Power lamp

flashing status Cause Corrective action

0.5s on/

0.5s off

(slow flashing)

The internal

temperature

exceeded the

preset limit. The

tool has stopped.

(The motor turns

off. The power will

shut down

automatically after

one minute.)

[Temperature

protection

function]

Turn off the power

and wait for the

device to cool.

You can resume

use once the

device

temperature has

fallen.

Power lamp

flashing status Cause Corrective action

0.1s on/

0.1s off

(rapid

flashing)

The tool

attachment load

exceeded the

preset limit. The

tool has stopped.

(The motor turns

off and the lamp

flashes for

10seconds.)

[Overload

protection

function]

Turn off the power

and remove the

battery. Resolve

the cause of the

overload.

You can resume

use after resolving

the overload

cause.

MAINTENANCE AND INSPECTION

WARNING

Pull out battery before doing any inspection or

maintenance.

Maintenance safety

○ Maintain the unit/machine according to recommended

procedures.

○ Use only genuine HiKOKI replacement parts as

recommended by the manufacturer.

WARNING

Improper maintenance could result in serious machine

damage or in serious personal injury.

1. Checking the condition of the cutting attachment

The cutting attachment should be checked regularly. If

worn or broken cutting attachment can slip or decrease

the efficiency of the motor and burn it out.

Replace worn cutting attachment with new ones.

CAUTION

If you use a cutting attachment of which point is worn or

broken, it will be dangerous. So replace it with a new

one.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

5. Cleaning on the outside

When the power tool is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

6. Gear case (Fig.26)

Check gear case or angle gear for grease level about

every 50hours of operation by removing the grease

filler plug on the side of gear case.

If no grease can be seen in the screw hole on the sides

of the gears, fill the gear case up to 3/4 full with quality

lithium based multipurpose grease (sold separately).

CAUTION

○ Make sure to remove any dirt or grit when attaching the

plug to its original position.

2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18

CG18DA(L)_C99750571_311_EU

Hikoki CG18DA Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info