Bedienungsanleitung Hikoki CG18DA (Seite 22 von 380) (Alle Sprachen)

816209

Zoom out

Zoom in

Vorherige Seite

1/380

Nächste Seite

English

○ Before attempting inspection or maintenance of the

gear case, make sure the case has cooled.

7. Semi-auto nylon head

Nylon line replacement

(1) Remove the case by firmly pushing inward the locking

tabs. After removing the case, take out the reel and

discard the remaining line. (Fig.27)

(2) Rotate the button in the direction of the button arrow

mark, and align the nylon line guide and the reel groove

in a straight line. (Fig.28)

(3) Starting from the nylon line guide, insert the nylon line in

the direction of the reel arrow mark and pass it through

the reel groove, then pull it out to the nylon line guide on

the opposite side.

Make the nylon line the same length on both ends.

(Fig.29)

(4) Rotate the button in the direction of the button arrow

mark, and wind the nylon line onto the reel.

The initial cutting line length should be approx.110–

140mm and should be equal on both sides. (Fig.30)

(5) Place the cover over the case so that the locking tabs

on the cover meet the locking holes of the case. Then

push the case securely until it clicks into place.

CAUTION

Ensure that the hooks are securely hooked onto the

latch in 2places.

If the area around the latch becomes clogged with dirt,

etc., it may not be able to lock securely, so clean it

periodically to remove dirt.

8. Blade (Fig.31)

WARNING

Wear protective gloves when handling or performing

maintenance on the blade.

○ Use a sharp blade. A dull blade is more likely to snag

and thrust. Replace the fastening nut if it is damaged

and hard to tighten.

○ When replacing blade, purchase one recommended by

HiKOKI, with a 25.4mm (one inch) fitting hole.

○ In the case of a 3tooth blade, it can be used on either

side.

○ Use the correct blade for the type of work.

○ When replacing blades, use appropriate tools.

○ When cutting edges become dull, re-sharpen or file as

shown in the illustration. Incorrect sharpening may

cause excessive vibration.

○ Discard blades that are bent, warped, cracked, broken

or damaged in any way.

NOTE

When sharpening blade it is important to maintain an

original shape of radius at the base of the tooth to avoid

cracking.

9. Storage

Store the power tool and battery in a place in which the

temperature is less than 40°C and out of reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

significantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, significantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to five times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when the

battery is disassembled and modified (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level:

(Nylon head) 92dB(A)

(Blade) 91dB(A)

Measured A-weighted sound pressure level:

(Nylon head) 82dB(A)

(Blade) 81dB(A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841

Vibration emission value

ah,

= (Nylon head) 7.8m/s2

(Blade) 4.5m/s2

Uncertainty K = 1.5m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use of

the power tool can differ from the declared total value

depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that are

based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time).

2023/09/08 13:57:15Stylesheet: EU Version: 2023.8.18

CG18DA(L)_C99750571_311_EU

Hikoki CG18DA Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info