Bedienungsanleitung Hikoki D13 (Seite 3 von 100) (Alle Sprachen)

816291

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

DRILL SAFETY WARNINGS

Safety instructions for all operations

a) Use the auxiliary handle(s).

Loss of control can cause personal injury.

b) Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

Safety instructions when using long drill bits

a) Never operate at higher speed than the maximum

speed rating of the drill bit.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

b) Always start drilling at low speed and with the bit tip

in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

c) Apply pressure only in direct line with the bit and do

not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

1. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

(Fig. 11)

2. Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

3. Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

4. When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

5. Never wear gloves during operation.

Gloves are sometimes caught by rotating parts, resulting

in serious injury. Do not use gloves during operation.

6. Install the side handle and hold the tool ﬁ rmly with both

hands.

One-hand operation is very dangerous. Always install the

side handle and hold the tool with both hands. Holding

the tool insuﬃ ciently can result in serious damage during

operation.

7. Hold the main handle by your right hand.

Holding the main handle by your left hand may make the

switch be unintentionally locked.

8. Pressure

Drilling will NOT be accelerated by placing heavy

pressure on the drill. Such action will only result in a

damaged drill bit, decreased drilling eﬃ ciency, and/or

shortened service life of the drill.

9. The larger the drill bit diameter, the larger the reactive

force on your arm. Be careful not to lose control of the

drill because of this reactive force. To maintain ﬁ rm

control, establish a good foothold, hold the drill tightly

with both hands, and ensure that the drill is vertical to the

material being drilled.

10. When the drill bit bores completely through the

material, careless handing often results in broken drill

bit or damage to the drill body itself due to the sudden

movement of the drill.

Always be alert and ready to release pushing force when

drilling through the material.

11. Never change the direction of rotation while the motor is

rotating. Turn the power switch oﬀ before changing the

direction of rotation.

12. Precautions on boring

The drill bit may become overheated during operation;

however, it is suﬃ ciently operable. Do not cool the drill

bit in water or oil.

13. Caution concerning immediately after use

Immediately after use, while it is still revolving, if the Drill

is placed on a location where considerable ground chips

and dust have accumulated, dust may occasionally be

absorbed into the drill mechanism. Always pay attention

to this undesirable possibility.

14. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

D13 : Drill

To reduce the risk of injury, user must read

instruction manual.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive

2012/19/EU on waste electrical and electronic

equipment and its implementation in

accordance with national law, electric tools

that have reached the end of their life must

be collected separately and returned to an

environmentally compatible recycling facility.

V Rated voltage

P Power input

n0No-load speed

Switching ON

Switching OFF

000BookD13.indb3000BookD13.indb3 2022/12/2712:26:462022/12/2712:26:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki D13 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info